# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
# 2
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
Easy install, took around 30 minutes by my self to install. Hardest part of install was torquing the bolts ! Installed 13322 Class III Hitch - Gm 1500/2500 Pickup and Curt Class III Ballmount -2ball-2 Drop
# 3
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 4
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
I purchased the etrailer.com 2-3/4 " Rise or 4" Drop Ball Mount Kit, Curt Trailer Hitch Receiver and Twist-in 7-Pole RV-Style Trailer Connector for my 2011 Chevy Silverado. Quick Delivery! All the necessary parts arrived in perfect condition. Directions were spot on and the instructional videos were great.
The drop ball mount is the perfect size for my Jeep. The versatile hitch balls are convenient. Thank you for putting together a great kit, providing excellent communication, and delivering it quickly.
# 5
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 6-3/4" Long - 3,500 lbs
Sturdy. Shipped quick.
The whole process was as painless as it could possibly be. After reviewing my choices on their website, I ordered the trailer hitch by phone. Cathy was knowledgeable and efficient and everything I need was quickly ordered. Shipping time was short and I was very satisfied with the packaging. The hitch itself looked great. Installation instructions were clear and it is easily a do it yourself project. I had a local garage install mine and it took less than 15 minutes. ($25). The only "problem" I had was that the receiver I ordered came with a lock pin so I did not really need the separate pin I ordered. However, it's always good to have a spare.
# 6
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
I am very pleased with the hitch, ball mount, and electrical package. All were easy to install if you follow the easy to understand directions. An added plus for putting one of these on a MINI is that the hitch can be hidden behind the "black plate/cover" that is on the rear bumper. It looks just like it came out of the factory except when to need to install the ball mount. The service has been outstanding. This is the place to go.
# 7
Draw-Tite Ball Mount - 3/4" Rise, 2" Drop - 10-1/2" Long - 6,000 lbs
I had previously purchased the etrailer hitch for my 2021 Ford Transit 150. It was a little short in length and the bumper prevented my current ball mount from working. As always, etrailer had the perfect solution. The Draw-Tite is well made and will now remain permanently with the van to be handy whenever the need arises.
It works fine, it's a drawbar. Etrailer is always easy to deal with and decent pricing.
# 8
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.
# 9
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
Excellent customer service & support! Bought for my 2013 Honda Fit and plan to trailer my Yamaha Tenere motorcycle around North America! Very happy with hitch.
Typical quality of...VERY good!! Lol. I've pulled my small mc trailer numerous times with this hitch and NO issues!!!
# 10
Curt Class II Drawbar - 3-7/8" Rise - 13-1/2" Long - 3,500 lbs
2013 Goldwing Motortrike receiver hitch to Bushtec trailer. etrailer was the only company that I could find that had the hitch in the right dimensions that I needed: Length of at least 12 ", and rise of at least 3.5 ". My order was processed and shipped faster than anything I have ever ordered over the Internet. I am extremely pleased with the price and service. I recommend etrailer to anyone needing hitch equipment.
This is just what I Need for my honda gold wing trike. This is the only draw bar that I could find that clear the bumper. I now can pull my Bushtec trailer without the nose being low to the ground.
# 11
Curt Class I Drawbar - 5" Rise - 9-9/16" Long - 2,000 lbs
For Mazda CX-3 owners, this is the drawbar you need to achieve the correct final hitchball height for small U-Haul cargo or motorcycle trailers. You know the receiver sits quite low so this gets the height just where it needs to be, especially when the trailer is properly weighted/loaded.
Shipped in quicker than I thought it would. It fit it my old Hidden Hitch Class I receiver perfectly. I drive a '97 Geo Prizm, and the 5 inch rise is a definite plus in keeping my 5 x 8 utility trailer nice and level when I'm hauling lawn equipment. The only drawback is that the Curt drawbar does not come with the pin.
# 12
Curt Towing Starter Kit for 1-1/4" Hitches - 2" Ball - 3/4" Rise - 3,500 lbs
Keep with spare tire out of weather to prevent rust.
Every Curt product we've purchased over the years has been perfect. Quality, fitment, price, etc has been spot on. The Curt products are far better made than Reese and Draw-Tite. Not even close!
What our customers are saying:
"very easy to shop"