You're loaded up after dark and rolling out. This light handles the signaling and keeps your plate visible. It's wired in, sealed tight, and built to take the rough roads, water, and bumps along the way.Passenger-side light (TN62XR) and wiring sold separately.
You're loaded up after dark and rolling out. This light handles the signaling when and where it matters. It's wired in, sealed tight, and built to take the rough roads, water, and bumps along the way.Driver-side light (TN42XR) with license light sold separately.
It doesn't take much to crack a trailer light, one rock or bad bump and it's time to replace. This steel guard adds a layer of protection so your lights stay safe on the road and job. ... Specs Dimensions: 8-5/8" long x 4" tall x 3-3/4" wide Application: Mounting box for 6" oval and 2" round lights Fits left or right side Mounting: Weld-on or bolt-on installation Mounting attachment center: 2" Construction: Steel Raw finish (unpainted)
Features: Helps to protect exterior lights from the elements Designed for (1) 6" oval light and (1) 2" round sidelight (both sold separately) Black powder-coated steel construction Overall dimensions: 8" wide x 3" tall x 3" deep
Hey Ted, thanks for reaching out. I went out to our warehouse and measured the Dexter Light Box Guard #DX99VC. The oval cutout is indeed 6-1/2" long x 2-1/2" tall. The 2" side light is supposed to be just a clearance light for…
Yes, you can use a fuse tap like the part #F2526 to tap into the stoplight circuit of the vehicle for a dedicated brake signal for installing a brake controller. Any time the brake lights are turned on this circuit would have voltage on it.
The best thing you can do to eliminate those streaks is regularly clean your trailer because there just is not a way to re-route the condensation before it leaves streaks. The best way to do this is by using the Griot's Garage Rinseless Wash and…
Hey Dan; there isn't an actuator that will slide in place for a replacement of your Tie Down 80LP, you'd have to go with a new actuator. From what I can find, this actuator bolts onto a 3" wide channel tongue, so you can replace it with…
I looked up the information on your TDE 46205 Hubs and found a couple of great replacements for you. The one you pick will depend on the number of wheel studs you have. For 5 wheel studs use the etrailer Trailer Idler Hub Assembly for 2,000-lb E-Z…
Your 4-pin/5-wire wiring harness is what is called a "wishbone" type which simply means that there are two separate running light wires, one brown and one pink. This allows a separate running light wire for each side of the trailer which…
The Curt Trailer Hitch Receiver #C84BR is not the same shape as the Ford OEM hitch but the installation process is similar. Like the OEM hitch, the Curt hitch will bolt onto the frame and sit behind the rear bumper so the end result will be the same.…
If the outer diameter of your spindle where the seal rides is 1.719 inches and the diameter on your hub is 2.565 the #RG06-050 would be the closest matching grease seal we offer. You will need a digital or dial caliper for this measurement like…
If the inner diameter is 1.719 inches and the outer diameter is 2.565 the #RG06-050 would be the closest matching grease seal we offer. You will need a digital or dial caliper for this measurement. The grease seal number you referenced doesn't…
Hey Bear! Yes, you can lock up the coupler part of your Demco DA86 Actuator #DM68CV with either the Trimax Pin #TMX38SR, or the InfiniteRule #IR56FR if you're looking for a high-end lock. Is this the type of lock you had in mind?
Buyers Products tail light mounting box. Designed for (3) 4" round DOT lights (sold separately). Stainless steel construction.Features: Buyers Products tail light mounting box Designed for (3) 4" round DOT lights (sold separately) Helps to protect exterior lights from the elements Stainless steel construction Overall dimensions: 18" wide x 6" tall x 3" deep
This steel mounting box protects 2 exterior lights from the elements. 4-1/2" Diameter round viewing holes and a black powder coat make the box perfect for mounting on your truck.Features: Mounting box protects 2 exterior lights from the elements Steel is weather resistant and durable Black powder coat adds a rugged look Box has (2) 4-1/2" round holes Dimensions: 12-1/4" long x 6" tall x 3-1/2" deep
Filters
