Result: MAGNETIC

To test the Brake magnets with an ammeter,item # PT89ZR, you would connect the ammeter between the positive terminal of a battery and one of the magnet wires, then connect the other magnet wire to the negative battery terminal. |

No, the Buyers Products Magnetic Mounting Plate # 3378895404 are just the magnetic plates that a magnet would stick to; the magnets themselves would need to be supplied. | Does...

| Magnetic switches such as the Lippert Components Kwikee Step Switch Magnet # LC369299 operate by their magnetic fields interacting. | Do the two magnet actually need to touch or just be...

e28JR this part is described as magnetic? How so? is the while thing a magnet? what purpose does this serve? | e28JR this part is described as magnetic? How so? is the while thing a magnet? what purpose does...

The 3.7 ohms reading on your brake magnets does not indicate that the brake magnets need to be replaced. | I am getting a ohms reading of 3.7 on my 12x2 inch dexter breaks do I need to replace the magnets...

Replacing the magnet is pretty easy. On the control arm that holds the magnet there is a spring. | I need to know what is the amp draw on a single round dexter magnet. Also how is the magnet mounted to...

Is it normal for the magnet to have residual magnetism. I had a screwdriver on the magnet and when I released the brake controller the screwdriver was held up. | Is it normal for the magnet...

How do you measure a magnet in order to decide if it needs to be replaces? | How do you measure a magnet in order to decide if it needs to be replaces? Thanks | I would check the magnets for wear before going on to test...

If the readings are too high or too low, the magnet(s) will need to be replaced. To test for a short, disconnect the battery negative wire from the brake magnet wire and connect the base of the brake magnet to the battery negative post. |

4 dots are still showing on magnet and magnet looks good. Can I just ground the non-12 volt wire directly to ground to test my ground to that magnet? | I have a Hudson, 12foot single axle...

For 7 inch brake assemblies, the magnet should read 3.0 to 3.2 amps. If the amperage readings are greater than the specified amounts, replace the magnet(s). | How can I test the unit to see if it is putting...

If my brake magnet has a lot of rust on it will it still work? | If my brake magnet has a lot of rust on it will it still work? I have power going to my brakes but they are not working? | Excessive rust would definitely weaken...

There are a couple of magnetic tow lights that have specifically stated the anti-scratch elements of their magnets. | do your magnetic tow lights have a protective surface that does not mar the paint | There...

Is this a pair of magnets or just singles? | Is this a pair of magnets or just singles? | The Replacement Magnet Kit # AKBRKR-M12 that you referenced is an individual magnet with a spring and retaining clip. If you need two...

I want to replace the magnets on my Jayco 32dsbh. The axle is 4400lbs, but i cant find 4400lbs rated magnets. | I want to replace the magnets on my Jayco 32dsbh. The axle is 4400lbs, but i cant find 4400lbs...

Testing individual brake magnets for proper function can be accomplished by severing the magnet wires and connecting the ammeter between the positive terminal of a 12-volt battery and one of the magnet wires; it does not matter which one. |

I have a 2000 Travel Supreme RV Build date is 12/99 3- 7000# Dexter axles 12inch Drums and 2.5inch brake pads. Magnets are red wire 4inch X 2.5inch in size What is need are 3 magnet retainer clips for this size magnet. |

Describing the strength of the magnets used on the Optronics Magnetic Mount Tail Lights would be fairly difficult, as magnet strength is pretty subjective. | How strong are the magnetics?...

Keep in mind that the thickness of the metal the magnet is placed on will also have a bearing on how well the magnet adheres. | Tow lights gauge of wire and strength of magnetic? Also...do you charge a sales...

Do you sell magnet keepers to keep magnet on 8000 lb. Dexter axel brakes? | Do you sell magnet keepers to keep magnet on 8000 lb. Dexter axel brakes? | If you just want the magnet clips, you will use the Replacement...

You will need to get the magnets warmed up and then check the resistance in the magnets. | My electric trailer brakes have a short only when moving. I know this because my controller has a red LED to show when...

In your description to test magnets you write: Next, disconnect the negative wire from the brake magnet wire and connect it to the base, housing, of the brake magnet. | In your description...

Finally, using an ohmmeter, check the resistance between the brake magnet wires. If the resistance is not within the specified range below, the magnet will need to be replaced. 7 inch brake magnet resistance should be 3.8-4.0 Ohms 10 and 12 inch brake magnets resistance should be 3.2-3.5 Ohms If the magnets just need to be replaced, we carry various types and sizes of magnets. |

The next section of our brake magnet testing article details how to test each magnet separately to determine if one or more of the brake magnets on your trailer is defective. | The article...