!Liberty Travel Trailer  x   >   !FLD-Series  x   >   Gen-Y Hitch  x   >  

I have a cargo carrier that I want to raise so it doesn’t hit the ground going over bumps off curbs etc.. I don’t need the 2nd 2 inch port for hauling a trailer and I do not need the 1 1/4 reduction. Basically looking for exact same device but...

Does the hooked end have a 3/8inch thickness? | I checked with Gen-Y and they informed me that their ramp set part # 325-GH-R96 is made from a double hollow tube, 3” x 5”, with a wall thickness of .125 A6063 alloy. This includes the hook end...

I currently have a 2014 Grand Design Reflection 337rls. I tow it with a 2021 GMC Sierra 2500 Duramax short bed and have the BandW turnover gooseball installed with the BandW Slider companion hitch. I am looking at switching the pin box to one...

Do they make one with a 4 inch drop. My xterra sits high and i normally use a 4 inch hitch for my popup | The Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers # D210 does not come in any other drop. If you need...

I have a 2017 Forest River, Forester 3051S See attached photo of my hitch set up. At times, the hitch bottoms out and hits concrete or pavement. There ate two protective V's that can be seen where contact is made, so not direct contact with...

There seems to be some left/right wiggle on the puck feet after I installed this hitch in the 24 F250. Do you have any suggestions that might be the cause or is that normal? Theres probably 1/8 play if you push on the rear puck areas | Hey...

What weight class is this rated for? I will be using with a class 4, 2inch receiver towing 8K pounds. | The Gen-Y Iron Grip Anti-Rattle Hitch Pin for 2" Hitch Receivers # GY39FR is rated for 21,000lbs. So you will have no issues using this with...

Is this item made in USA? | The Curt Class III Ball Mount with 2-5/16" Ball part # C45041 is not made in the USA but we do have options that are like the B&W Heavy-Duty Ball Mount part # BWBMHD30010. This is not a complete kit though so you'd...

Hello, I have a 2010 keystone cougar 326mks. It currently has a king pin hitch, but Id like to buy one of the gen-y or Reese gooseneck hitches, but I cant figure out which one replaces it. Could you help me? Thank you, Eric | To give you the...

I am looking to get a 5th wheel trailer but I will need to convert it to a gooseneck. What will I need to do and what do I need to buy? | You will need to get the model number of the pin box, some of the more common pin box types are the Lippert...

I am looking for replacement pins for my Gen-Y Adjustable 2-ball mount 325-GH-624. Do you guys carry those? | Yes! For the correct replacement pins for your Gen-Y Adjustable 2-Ball Mount # 325-GH-624, that is the InfiniteRule Lock Set for Gen-Y...

Question hope you can answer. Have a flat bed with a gooseneck. The ball is recessed some and wondering if there is a max distances the ball can be from the bed for this to hookup. Thanks. | That's a good question and I do have an answer for...

i have a road armor trailair hitch 19,000 ser # 4ydf33121ma741192 was need know what Reese Goose Box™ 20k Gen 3 5th Wheel Pin Box i need | Thanks for the information! The Reese Goose Box 5th-Wheel-to-Gooseneck Air Ride Coupler Adapter item...

I have a 2019 2500 short bed chevrolet. My camper is a 2021 grand design reflection 150 series. Which one of the 3 reese fifth wheel to gooseneck adapter will best serve my purpose? I just want to make sure I dont need an offset, etc or any...

Not sure what Model Pin Box I have. Its made by Lippert and I think its a Rhino Box? No Model? What goose box will fit my application? | Thanks for the picture! I just heard back from my rep at Lippert and your 5th wheel trailer has a Lippert...

Do you have a dual hitch adapter that can both pull a trailer and support a bike carrier? | I have a solution but all dual hitch adapters are only rated for flat towing. To tow a trailer and haul a bike rack off of your vehicles hitch, I recommend...

Could a winch be mounted with this if the winch is mounted on the right type of receiver mount? Question would be...if it could sustain the pull wt. | I do have a solution for you but when I reached out to my contact at Roadmaster they did...

I need a hitch that will at least 6inch and then raise up to a 1 or 2inch . Its for flat towing a vehicle behind my motorhome. The Patriot hitch looks perfect but it says its not for use in flat towing or tow bars. Do you have such a product...

Aluminum Car Hauler Ramp Set - 72inch x 14-1/2inch - 6,000 lbs - Qty 2 I have a Maserati with back tires of at least 12+ WIDE. This ramp may work but will it accommodate the tires of this size? The inner portion of your ramp may not fit the...

I have a class a motor home that I pull a enclosed car trailer. The trailer is rated at 10000 lbs gvw. The towing capacity of the motorhome is 10000 lbs. I have a ball mount that had a 2inch rated at 10000 lbs but my problem is I need a bigger...

Is there a cushioned ball mount that can be used with weight distribution? I dont see how it would work with this product.... Any suggestions would be very much appreciated! | For the Gen-Y Glyder Shock Absorbing Ball Mount for 2" Hitches #...

Why does your description say not for use when towing a trailer...can I have a bike rack on the high rise part and tow my boat with the other ? | I recommend using the Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers # 325-GH-226 for towing...

Hi, I had the dealership order a Reese Gooseneck box for my RV but when they installed it they stated the mounting plates had the holes offset about 1/2inch on one side. I had them deliver it to the campground this weekend while we wait for...

Does this hitch work with surge brakes boat trailer? | I spoke with Gen-Y about the Gen-Y Glyder Shock Absorbing Ball Mount part # 325-GH-12001 and they informed me that it can indeed be used with a trailer that has surge brakes. Therefore,...