!Cherokee Alpha Wolf Travel Trailer  x   >   SnapPad  x   >   Dutton-Lainson  x   >  

Does this jack have the clip ring? | The Dutton-Lainson Pull Pin, Easy Swivel Trailer Jack, part # DL22689, comes with the weld-on bracket and the retaining ring that connects the jack to the weld-on bracket and allows the jack to swivel. |

I have a 26 ft sea ray which is being pulled onto a carpeted trailer. what electric winch would you recommend | For your 26 foot Sea Ray I recommend the Dutton-Lainson StrongArm Electric Winch # DL25215. Based on my research your Sea Ray likely...

on the Fulton XLT strap replacement diagram how many screws need to be removed to take cover off in figure 11? Does the winch need to be removed from trailer to change the strap? | You will need to remove 9 screws to get the cover off of your...

I have a 2016 load rite boat trailer. Im missing my winch crank handle. The trailer model number is 21360096vtb. Not sure which to purchase. Thanks. | We offer a whole range of replacement crank handles for winches that you can see on the linked...

I currently have a DL1402A winch but due to have steps getting in my boat the winch handle hits the steps, i need a shorter winch handle or a winch with shorter handle. what do you recommend? | The Dutton-Lainson Hand Winch part # DL15303 comes...

Does this come with a strap? Description indicates polyester strap but not mentioned anywhere else. | The Dutton-Lainson Hand Winch - Worm Gear - Hex Drive - 2,000 lbs # DL11004 accepts a 2" wide x 20' long winch strap which is sold separately....

I have a galvanized steel boat hoist that I estimate to weigh in the 600 - 800 pound range. I am fabricating a frame to set on top of two blocks of styrofoam that previously supported a swimming raft. The dual drum winch would be bolted to...

does the dh22144 have a 5 1/2 holes that are 3 1/4 beewteen holes. | The bolt patterns that can be used on the Trailer Spare Tire Carrier and Dolly Bracket, part # DL22144, is 4 on 4 and 5 on 4-1/2. These bolt patterns are used on the 8 inch,...

I am not clear on how you roller bunks mount to my existing wood bunks. My current bunks are 6 FT and are mounted narrow side up. do the roller bunks go over the wood bunk and bolt directly to them and If I mount them that way do I need any...

I am going back to trailering my FourWinns 268 Vista. I believe I am around 6800lbs dry. It sits on a Venture trailer that has rollers. 1 Will the Fulton F2 work for me? 2 Is a strap ok or should I look at a winch with a cable? 3 Do...

BDW15017 Bulldog Winch: does.it come with a mounting kit for trailer mount and does it have a DC adapter. Im using it for 2001 Jayco Qwest pop up with after mkt airconditioner. The hand crank is very difficult. Does this come with.a crank if...

What size 12 volt electric boat winch do I need for an 206 inch stratos bass boat weight is around 2600 lbs | A great 12V winch for your 2,600 lb boat trailer is the Dutton-Lainson TW4000 StrongArm Electric Winch # DL25200. This is a marine...

Currently my boat is on a Coyote Inc. dual axel trailer in my driveway. Due to the slope of the driveway I really need to raise the trailer tongue up an additional 14 inches to get the boat bow up. Is easy way to do this? Is there an extra...

I am planning to replace my DL1100A manual winch with the DL-25200 one. Will the DL-25200 mount on the same base as the DL-1100a is mounted on now? Looks like the electric winch mounting footprint is about 9-1/16 x 3-5/8. Existing footprint...

What snap pads will fit 2013 Fleetwood Bounder 35k? My dealerships has no clue, the dealerships designated special tech help dept and Fleetwood.com has no clue. Ive even contacted Lipper have not got call back yet to find out what pads to purchase....

I have a Fulton A-frame jack thats about 30 years old. The outer tube is 2inch and the inner tube is 1-5/8inch or close to that. Are there casters to fit that tube? | The Replacement Caster Wheel for Ultra-Fab Manual 2" Trailer Jack - Qty 1...

I would like to purchase your Marine electric winch, but I notice it has no remote control. Please let me know if a remote control is possible on this model. Otherwise I will have to look elsewhere. Thank you | I understand wanting to have a...

what size would I need for a 4500lb boat, float on trailer, so it slides on bunks. | For a winch the boat-size-to-winch capacity is generally 2 to 1. With good rollers and short winching distances, increase the ratio to 3 to 1. With wooden bunks...

The diagram highlights all dimensions but the slot-to-slot center to center width. I am guessing 1 1/2? Thank you. | I called my contact at Dutton-Lainson and asked about the Boat Trailer Roller Bunk Bracket, part # DL21762. The center-to-center...

I cannot find the above kit on your website. Can you point me in the right direction? | The only Model 980 trailer coupler that Dutton-Lainson offers is the model 980 P-2 coupler, # DL13800. The correct latch repair kit for this coupler is part...

Can you tell me if the safety hooks will fit on a BW Hitch for a 2022 F-250? Is this unlike the Chevy 3500 problem that you responded to previously where the safety hook throat is too shallow? thanks | When it comes to using safety chains...

My question refers to what the parts that come with the repair kit DL 70451? If the gears are not damage on the winch, will this provide the springs and latches that operate the locking and unlocking of the wrench. | The Winch Ratchet Repair...

Is it true that there is such a place named HASTINGS, NEBRASKA USA. ? And is it a possibility that one could get there from here if he tried hard enough. ?!. The Missouri river trys to land me way off in Iowa 5oo miles out of the way of destination.....BROADW...

How do you keep crank handle in horizontal Position Do not want handle to face towards ground | Sounds like you are looking for a way to keep the handle of the Dutton Lainson jack part # DL22580 horizontal when the jack is in the horizontal,...