Result: curt bed rails

to the existing rail assembly under the bed of your truck. You'll need to cut a 3-1/2 inch diameter hole | I need a gooseneck hitch for a 2016 ram 2500 but I don’t see a hitch assembly just the hitch ball....

the wiring along the driver's side frame rail. There should be an orange wire with the 12V power and a blue | i have the factory ford 7 pin in the bed for the gooseneck, but i do not have a plug on the bumper, so by using this...

2020 Chevrolet Silverado's Bed Rails. Since the Lock N Roll Tonneau Cover doesn't cover up the stake | I have 2020 Silverado 1500 with a short bed and a lock n roll cover. We are looking for a rack to carry...

3/16 of space between the hitch and the frame rails on each side, in other words it was not a snug fit | Curt C13081 on a 2014 Jeep Patriot. We installed the hitch this weekend and noticed there was about 3/16 of space between...

The front stake pocket on your 2015 Ram 1500 is hidden under the plastic rail cap but there should | I have a 2015 dodge ram 1500with toneou cover. Want to put stake anchor and want to know how to open the front hole up. The...

with a flat bed. Thank you. | I was wanting to know will there be a problem installing the 57101 connector on my 2013 Chevy 3500 with a flat bed. Thank you. | If your 2013 Chevrolet Silverado 3500 flatbed already has a factory...

I purchased a 2-bike MonoRail from you a few months back - it shakes a lot in my 1 1/4” hitch | I purchased a 2-bike MonoRail from you a few months back - it shakes a lot in my 1 1/4” hitch receiver. Would this anti-rattle lock...

is compressed. Most likely the wiring is somewhere along the frame rails and where the body meet. I wish I | lights go out when weight is in the bed, hooked on the trailer. disconnect the trailer and lights still blink on...

of the trailer loft to the top of the truck bed rails. The installation kit I recommend is part # RP50084-58 | I have a 2013 toyota tundra with 4.6 liter and 6 1/2 foot bed. what custom hitch and kit do you...

of the truck at the rear bumper or can I tag into the wire harness in the frame rail? If I go to the frame | What is the cleanest way to wire this? Should I get an adapter to plug into the harness of the truck at the rear bumper...

. This plug is located at the end of the drivers side frame rail behind the rear bumper. Finally, if your | I bought your harness for my 2002 F250 and when I plugged it in, my existing 7 pin is no longer functioning properly...

upside down which will give you full use of your truck bed. this includes all the mounting hardware | Will the dh 1202 goose neck hitch fit my F350 diesel crew cab four wheel drive | The Blue Ox Diamond Underbed Gooseneck Trailer...

spliced into the wires in order to install the fifth wheel plug in the bed however that plug doesnt work | Hello, The truck I purchased used has a trailer harness installed and it looks like someone spliced into the wires...

check for the two built-in plugs located along the frame rail at the rear of your vehicle (see attached | Where do we look to verify we have an OEM tow package wiring for a Santa Fe 2015 versus no tow package ? | The contents...

Looking to use this as a outlet for a acdc portable fridge /cooler, in the bed of the truck | Looking to use this as a outlet for a acdc portable fridge /cooler, in the bed of the truck, instead of the one by the bumper. This...

Although the # 118243 shares the same rectangular plug located on the driver's side frame rail | I have a 2003 f250 that has both a 4 way and a 7 way with factory connection. I see 2 options for fixing this. Item # 118243 and...

tire and also on the drivers side behind the rear tire on the frame rail. This connector will most | I would like to install this on my 2000 Chevrolet C3500, but it doesnt have a factory installed hitch. Is the plug available...

I installed the CURT kit and the brake and headlights work on the trailer. No turn signals though | I installed the CURT kit and the brake and headlights work on the trailer. No turn signals though. All work fine with another...

mounted on bed rails, I have a clean unused 7-way plug, I have wire to connect the 2 lights to the plug | I have a 2014 chevy w2. Im wanting to use extra reverse lights for winter and I have the lights mounted...

and to the right of the spare tire on the passenger side frame rail as shown in the photo I've provided. if you | Hello, i am looking to install a curt trailer hitch and wire, and i see on your website. We have a 2012 Sorento...

Curt trailer wiring harness # C55255 is designed to fit as long as your 2004 Ford Escape came | I purchased this item and once I connected it to the plug behind the panel only the running lights worked. The blinkers nor the...

rail behind the cab which contains the wires for lights and signals. From there you will have to wire | Hi, I have a 2004 International 4300 series box truck. Id like to install a this brake controller, but Im not sure how...

I purchased a trailer wiring harness adapter for a 2005 Liberty Jeep. Item number, CURT 55382 | I purchased a trailer wiring harness adapter for a 2005 Liberty Jeep. Item number, CURT 55382 T-Connector, on Ebay. I am having...

slider hitch? I want to be sure I retain adequate clearance to the bed rails and tailgate. | I have a broken spring so am looking at this system as a quality fix and upgrade. I’m very handy with a good set...