1998  x   >   !SportRack  x   >   Ventline  x   >   CURT  x   >  

I have a 98 F-150 4 x 4 the electrical connector for the trailer on the truck chassis side has rotted off I cannot find a repair pigtail and connector for it can you help | Unfortunately we do not carry the OEM replacement pigtail for the 1998...

I have a 97 Jeep Wrangler 4.0. Im wanting to buy a horse trailer that weighs 1240#, has upgraded torsion axels and electric breaks 6foot wide. My horse is about 800 to 900#, in the winter, probably 1,000#. I see that the towing capacity is...

Good Morning I am looking to trailer tow my minivan with our bus and looking for a heavy class 3 or class 4 hitch. The fram3 rails are 35inch interior spaced and 18 inches above the ground, with bolts accessible for both side and bottom attachment...

Im confused on how to install the bolts on the passenger side because after I lubricated the holes, I tried to fit the 10.9 bolt and its too big. I have a 1998 Jeep Cherokee. | It is actually pretty common for the bolts to seem like they are...

I have a 1998 chevy silverado 2500 HD with a reading classic steal service bed and step bumper. Is this the correct hitch for me? Thank you | Since your 1998 Chevy Silverado 2500HD has a service bed on it currently that would indicate that...

will this trailer hitch fit a 1998 honda odessy | The Curt Trailer Hitch, part # C11211 is the only fit for your 1998 Honda Odyssey. This is a Class l hitch and has a 1-1/4 inch receiver opening. I have attached a link to some of the products...

I do not know if I have a harness presently on my motorhome. There is a 4 pin connector installed to go to the trailer harness but dont work. I cant get any electrical current to the 4 pin connector ? | I would first spend a few minutes trying...

I have a 1998 Ford Escort Wagon and I am worried about compatibility. The other products on your site makes it look like they are for the sedan and I want to double check to make sure the hitch is for a station wagon. I already have factory...

I have the above car and would like to use the Draw Tite hitch but, I am not sure if it will work with the Thule bike rack I have is a Classic model 9044. I see that the hitch is a class 1 with a tab. What does the tab do and will it prevent...

What is the distance from center of hitch pin hole to closest edge of carrier when carrier is NOT folded up? | The distance from the center of the hitch pin hole to the nearest portion of the Curt Cargo Carrier # C18100 when folded down is 8...

Im wondering what the measurements are of this. From end to end..Etcetera thank you | I spoke to my contact at Curt and he sent me a complete dimensional drawing for the Curt Hitch part # C12270 that I attached for you to review. |

I need instructions how to install fifth wheel hitch in a 1998 dodge ram 2500 4x4 long bed | You will need the Universal Fifth Wheel Trailer Hitch Installation Kit with Rails, item # RP30035, to install a fifth-wheel hitch in your 1998 Dodge...

Looking to upfit my 1998 Ford E350 15 passenger van with a 4 pin factory wiring setup to a 7 pin setup with a proportional brake controller. What are the right products I need? Concerned that the 15 passenger van might need longer wires to...

what type would you recommend for a standard bumper. | For a 1998 Dodge B1500 van with a standard factory bumper (and no weld nuts in the frame) the hitch I recommend is the USA-made Curt # 13015. I suggest this hitch because it has a higher...

I need an electrical schematic to install the wiring into my 1998 Winstar | The wiring harness for your 1998 Ford Windstar is a plug and play harness, part # C55346. It plugs into your tail light assemblies. I have also included a link to the...

i am having a problem with the wire harness to the left side brake light there is a wire shorting out can u help me to understand what i am looking for and how to fix it | To run down a short in a wire you will need to use a circuit tester,...

What is the dimension of the bolt holes side to side? I am hoping to use this hitch. My frame rails are 34 inches apart and the existing holes are 32 inches on center. Also what is the length of the mounting flange? What is the dimension of...

I have been all over the web forums. This hitch seems to work well, but I see 10 out of 10 installation difficulty. Do you have a set of detailed instruction or video to watch and which wiring harness is best? | I have looked over the instructions,...

Is the trailer hitch / harness option for a 1998 or a 1999 Chevy Tahoe going to be the same? Thank you | Yes, the trailer hitches that fit a 1998 Chevy Tahoe like the Curt # C14029 also fit the 1999 Tahoe models. This is also true for the trailer...

Ive lost all the hardware for C11169. . | Not a problem. What you will need is replacement hardware kit # RHK. On the RHK page you will enter the hitch number in the box near the add to cart button. Then select the manufacturer from the drop...

I just installed the Curt 57674 7-way adapter with test lights, the Tekonsha 118349 Taillight Converter Harness, and a Hopkins 47295 Agility Brake Controller on my 1998 Jeep Grand Cherokee. Installation was a breeze, and honestly it would be...

Hello, When it says 2inch hitch does that mean inside opening of hitch is 2inch to receive a bike rack or motorcycle carrier ? Curt states load must be supported ? Do they mean tie down web belts to hold load or support for the carrier ? If...

I am looking for a 5th wheel hitch for a 1998 Dodge Ram 2500 Crew Cab short bed 4X4 truck. Removable if possible but not absolutely necessary. Thank You. | You will be able to remove any 5th wheel hitch that is a fit for your 1998 Dodge Ram...

I have a 1998 Toyota Land Cruiser. According to the dealer, it did not have a factory trailer wiring harness. So I need to install one. I also need to install a trailer brake. I need I want to mount the wiring harness module in the vehicle,...