1998  x   >   !A6  x   >   !S-10 Pickup  x   >   Deka  x   >  

hello I purchased the dodge 5th wheel 7wire extension and i made a bad choice on the plug location in the front side wall,do you offer a 12inch or 18inch extension so my original bumper bracket can be reached with the factory plug. ?any...

was wondering if you had any videos of brake controller being installed on 1998 chevy blazer. And if you can tell me what color wire is the brake wire to tie into under the dash. I think I found it with test light, it comes on only when brake...

Im looking to install electric brakes on my trailer and brake controller in my vehicle. Vehicle: 1998 Jeep Cherokee has 4 pin connector Trailer: Aluma 7712H with factory axles Aluma says 3500 lb rated at 2990 lb EZ lube. Axle has 4 hole square...

I have to replace the vehicle-to-trailer connector on my Grand Cherokee Laredo 98. It has 5 wires that turns into a 4-flat connector. Colors are: Red Green Yellow Brown White I have a Vehicle wiring harness from your company- it only has Gr/Br/Ye/White...

I am installing one of your Curt brake controllers on my 1998 Chevy K3500 pick-up. I purchased the Curt #51451 harness and it doesnt seem to have the right plug to connect to the trucks electrical box. Did I have the correct harness? Thanks...

I have installed a CURT Manufacturing 55486 T-Connector kit on my 98 Rav4. The trailer lights work intermittently or not at all. I have ground to bare metal taillight bracket and hole ground to bare metal the grounding screw and used a n eyelet...

Hi, I need to adapt a round 4 pin connector female with round pins on a Motorhome to 7 pin connector so I can hook up a tow dolly with brakes. Do you have anything that will work? Thanks. | I'd recommend you use our Brake Controller Installation...

Looking to upfit my 1998 Ford E350 15 passenger van with a 4 pin factory wiring setup to a 7 pin setup with a proportional brake controller. What are the right products I need? Concerned that the 15 passenger van might need longer wires to...

I have a 1998 chevy suburban c1500. It has factory installed heavy duty tow wiring with the orange and blue wires running front to back. Ive located them in the back and going to hook the orange to the 7 way round connector, Im not hooking the...

I have a 1998 4runner that will be towing a tear trailer. The trailer has a round 7 pin connector. I have the 7 pin receptacle to match the trailer plug. I wont be needing trailer brakes but the trailer has a battery which will be trickle charged...

Do you sell the bolts and washers and nuts for a hitch? I have a 98 windstar and I have the hitch that was taken off it, I want to put it back on but need bolts, leaders and a wiring quick kit. Thanks for any help you can give. | We can obtain...

I have a 1998 chevy 1500 extended cab, I am installing an electric brake controler. I found the blue trailer brake wire blanked off in the left rear frame rail to use in the 7 pin connector, the only problem I have is I can not find the other...

is it ok to connect the red brake wire supplying power from the peddle to the trailer plug back at the plug location instead of directly at the peddle switch | You wouldn't be able to access the brake lamp signal at the trailer connector because...

what all do I need to install 4way ,7way andbrakes all in one | You will need to start with a 4-way on your 1998 Chevy Express Van. For that you would want the # C55335 that you referenced. From there you would need to convert the 4-way to...

I have a 1998 K2500 Chevy Suburban. I have the 7 way plug installed in the back and everything except the center aux. pin is hooked up. I recently bought a new trailer with a 6k winch and battery installed. The salesman informed me that the...

Looking to add electric brakes to my utility trailer. 2000/2200lb axle. 12 wheels. No backing plate installed. Can you give me a parts list of what Ill need? I dont find drums for your 7x 1 1/4 brake kits. | To add electric brakes to your...

I have power at the plug on the truck, but no running lights,or tail lights,or turn singals | If the connector on your pickup shows power for the lights when you test it then the issue should be on your trailer. You can verify this by connecting...

If my 6 way round connector on the truck does not have power to the auxillary, how do I get power to it? | You will want to run a length of 10 gauge wire like our 10 Gauge Primary Wire # 10-1-1 through a 40 amp circuit breaker like our part...

Will this work on my 1998 Jeep Grand Cherokee Laredo 4.0L ? | Yes, the Curt Venturer part # C74VV can be used on your 1998 Jeep Grand Cherokee with a factory 7-way. Next, for a wiring kit to install the brake controller to the 7-way you would...

Hi, I have a 98 2500 Dodge Ram that according to the build sheet came without trailer wiring, I want to wire the truck with a 7 pole harness so I can pull a gooseneck horse trailer. Ive installed the brake controller and connected it to the...

Hello, I have a 1998 International 3400 series Bus and need help with how to wire up the 7 way plug and a Tekonsha Voyager Trailer Brake controller to my Bus. I ordered a kit from yall for a 2002 chevy van and it was real easy, but it helped...

What do I need to add a brake controller to my truck and change my flat wiring prong at hitch to a 7way ever plug? Is there any wiring kits I need? Thanks | To add a brake controller to your truck and swap out the connector with a 7 way you'll...

What all do I need for installation of this controller for the easiest installation Thanks | To help installation of the Curt TriFlex Trailer Brake Controller # C24VV go smoothly, you will want a 4-way connector, the universal wiring adapter...

are electric brakes recommended for boat trailers? Bob G answered yes in one response. id like to get a second opinion. | Yes, electric brakes can be used on boat trailers. The brakes will not be damaged by going in and out of the water. Electric...