!V70  x   >   !5  x   >   Marlboro  x   >  

Can I shorten this hinge? | Yes, if you wanted to cut down the 3" Wide Continuous Hinge # MA75VR to shorten it you certainly could. |

What is the recommended weight that this hinge can handle? | I reached out to Marlboro Manufacturing and found that the load carrying capacity of the Weld-On Hinge w/ Brass Bushing and Grease Zerk # MA89ZR is 576 lbs. |

Can this hinge be shortened? And would this be suitable to be used for a ramp door extension or would there be a better product? | Yes, the 6' Long, 4" Wide Continuous Hinge # MA85VR can be cut down to the length needed. It is a 270 degree...

I have a Morryde 3000 on my fifth wheel. What size zerk fitting do I need. Back zerk broke off . Thank you | The grease zerk fitting on your MORryde 3000 is M6 x 1.0 according to my contact at MORryde. To replace this you need the following...

How much weight can this support and can it come in 8foot | Hinges like the 6" Wide Continuous Hinge - 6' Long - 1/2" Pin Diameter - Steel # MA52VR do not have weight capacity ratings and it is up to the installer to determine if it will be...

I have a need for 2 sets of hinges 50inch long for a door 70inch wide constructed of stainless steel - overall weight 600# materials Stainless Steel Please advise if your hinges with 1.2inch pin will be capable of handling the load Mounting...

Im looking for barrel Is hinge for my horse trailer tack room door. | Hello Kristine. We carry quite a few hinges and barrel hinges, so we very well may have what you need. If you can provide some dimensions for the hinge, I can take a look...

How much weight can this hinge hold? Thanks | Hinges such as the Weld-on Barrel Hinge # MA29ZR are not given specific weight ratings as that is at the discretion of the fabricator. There's way too many variables to give a standard weight rating. I'd...

Hello, I would like assistance in ing the appropriate hinge for my application. The application is we have a 200+ lb metal cover, which will be used to protect equipment. The only support the hinges have are the front lip of the trailer, where...

ID LIKE TO USE THE 6inch PIANO HINGE TO HINGE A CONVENTIONALLY FABRICATED WOODEN WITH 2inch LUMBER ATTIC STAIR IN MY GARAGE - INTENT WOULD BE TO DRILL MOUNTING HOLES INTO HINGE ON 4inch CENTERS AND BOLT HINGE TO ATTIC JOISTS / STAIR ASSEMBLY...

What size is the low profile zerk grease fitting? When the trailer hitch side was welded, the fitting was ruined. Too much heat froze the ball bearing and one cannot grease. | I spoke to Lock N Roll and they use 6mm x 1 low profile zerk...

can you tell me what weight these hinges are rated for? Weld-On Hinge w/ Brass Bushing and Grease Zerk - Steel - 3-3/16inch Long - 5/16inch Pin Diameter Item # MA39ZR | The weight capacity of the Weld-On Hinge w/ Brass Bushing and Grease Zerk...

Looking for cargo door hinges, for Coachman Chaparral 2017 model M-381 RD , thank you! | Usually RV cargo door hinges are piano style hinges that are between 3 and 4 feet like the part # MA85VR which is 4 foot long. This could also be trimmed...

Does it come with pre drilled holes? | The 3" Wide Continuous Hinge # MA75VR that you referenced does not come with holed drilled. We do not have any similar options that are pre-drilled. |

Was thinking about using something like this on a belt puller clamp, but we do not need the full 6foot length. Could we cut this down to something around 16-18? If no we may just weld on a couple smaller hinges | Yes, the 4" Wide Continuous...

part number MA37ZR, will these hinges support a b-fold utility trailer ramp gate? I want to use them for the folding part of the ramp, I would use three of them | Yes, the Butt Hinge w/ Non-Removable Pin # MA37ZR will hold your ramp just fine....

Can this hinge be cut down? | Yes, the Stainless Steel Piano Hinge # MA34ZR can be trimmed down. You will be able to weld it or drill holes to mount the hinge for your application. |

Im looking for a piano hinge for a 1995 Starlite pop up camper rear fold down door. It is 2x 83 1/2 with 1/4 pin. | We currently only offer a 2" piano hinge with a 1/4" diameter pin in a 72" length so you would need to purchase two and cut one...

I need to know the load limit or weight bearing in pounds for 2 different continous steel hinges. Ma75vr Ma45vr Also do you have sane time of these hinges in 3 feet length? If the 3 feet length is available what are the part numbers and weight...

Who sales them why is it so hard to find, I have a 92 skyline nomad , can not find door replacement LH hinges , rectangle 2by72 | With your trailer being 30 years old most parts are discontinued at this point so a lot of troubleshooting and...

Does this hinge have any kind of coating to prevent rust? Or does it need painted? | The 4" Wide Continuous Hinge - 6' Long - 3/8" Pin Diameter # MA85VR is made from mill finished steel with a commercial die cut quality, however they are not...

Can I cut it down to 7’ and not rune it? | Yes, you can cut the 8 foot long hinge kit part # MA32VR down to 7 feet in length and it would work great. |

I need a replacement Zerk fitting for a skid wheel. What size do I need for the following model? and do you carry? 48-979023 UltraFab Weld-On Jumbo Steel Roller Weld On - 2-1/2inch Wide x 3inch Tall Item UF48-979023 | Hello Gaby. I reached...

What is the suggested weight limit that this product can handle? | The Butt Hinge w/ Non-Removable Pin, # MA87ZR does not have a weight rating. |