!Outback Wagon  x   >   !Seaflo  x   >   !Nissan  x   >   LubriMatic  x   >  

I have a 2014 Ram 2500 I just totally rewired a trailer that I restored Ive got all lights working turn signals brake lights, clearance lights but when I turn on my hazard light on they work but not when I turn on my headlights | What you describe...

Hello, can you recommend a molybdenum grease available in size 3 oz tube for use with a miniinch grease gun for portability? The BlueOx SwayPro appears to require molybdenum grease and Im having trouble finding it in 3 oz tubes. Thank you. |...

I have a 2002 EZ Loader 2350LB capacity boat trailer. GVWR 2,960LB Model: 2-EZLBW90B 172350NB I want to replace the entire hub assembly because they are very rusty boat in saltwater so I am looking for galvanized hubs that include the pre-greased...

Hi - Im looking to purchase a trailer vehicle wiring harness for a 2014 Mazda CX-5 Touring AWD, but I am unsure if my tail lights are with or without LED. How do I find that out? Thanks! | The easiest way to tell the differencve between LED...

Hi I have a 2017 Lexus NX Gas Model. I found a 12 V socket in the driver side of the trunk. Can I connect the T-One T-Connector to the 12V socket so I dont pull the wire all the way to the battery under the the front hood? Please advise and...

I have a 1996 Wilson tilt trailer. A single car hauler. Double axle. Do you have parts for it ? See attached pictures. | Thanks for your pictures. They were extremely helpful! What you will want for your 1996 Wilson tilt trailer is the Trailer...

I have a dual axle trailer with 7000 lb dexter axle dexter PN 297697. What size and part my number is the correct rear seal. Also what is the correct packing grease. Thank you | For a Dexter 7k axle the correct grease seal is the part # RG06-070....

Can you assist with hard wiring connections of light bar with Tundra? | The Rampage SuperBrite LED Tailgate Light Bar part # RA960137 is very simple to install and will only require one hardwire connection. I have attached the installation instructions...

1997 Chevrolet Venture LS. Installed part #C55355 according to instructions. Found the harness connecter right away, no problem. Everything works with a test light. But when I plug in the trailer, the turn signals no longer function. No power...

Do you have to clean the bearings or can you just add grease. I have a 16foot toy hauler, used about 5 times a year for the past two years. | I would remove the hubs and clean the bearings and the inside of the hubs. Just adding grease will...

Turn truck lights on and trailer lights only clearance lights work, no turn or brakes. Turn off lights and the turn and brake lights work fine | The wiring issue you have is common and easily solved. The cause for your running lights to create...

What grease is compatible with part # AKIHUB-545-35-PG-K. Thanks. | The Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2 # AKIHUB-545-35-K is pre-greased but for when you are looking to grease the bearings you can use the LubriMatic...

I have no rear parking lights on my 2011 F150 but the blinkers work and the brake work theres no license plate light checked the trailer connector coming out of the harness and they cant seem to have power I also checked position 39-43 and 67...

I have a BWRVK3370 that is about 2 years old. I purchased it used after being used very little. It appears the previous owner lubricated the polyurethane bushings with a non-lithium grease. I understand using non-lithium grease can damage the...

I have a question about how to find out which wire is the signal, brake and stop light for a 2001 lexus rx300. It is a single light bulb with 3 wires. The turn signal has its own bulb. Please help. | To determine which wire, control the turn...

I recently ordered a part #20135 for my 2004 jeep grand Cherokee, i received the part and it wasn't quite what i expected, i knew my jeep had a connector behind the rear kick panel for trailer wiring, i assumed this was the connector referred...

Hi, I have the same issue as this one listed in your QA Trailer Tail Lights Not Working after Installing Tow Ready Wiring # 118491 on a 2009 Honda Pilot I have a 2010 Honda Pilot and installed the wiring kit 118491 I followed the troubleshooting...

2 years ago I purchased your trailer hitch, it came with the wiring. After I installed it I never could get any current to the trailer. i live on a lake, so I just didnt bother to follow up because I only use my boat trailer 2 time a year. One...

Hello, I have a 2016 Toyota 4Runner, and I have wired the Redarc Tow Pro Elite to the Toyota factory brake controller harness using the instructions in the question on this page 281269. The trailer running lights are not working with this wiring...

In the manual it says to grease with High-Pressure Wheel Bearing grease, what do you recommend that comes in a cartridge? | Your Curt A30 5th Wheel Trailer Hitch Item # C16070 has a zerk fitting on each side of the jaw. A high temperature wheel...

My 18 explorer came with a 4pin and i need a 7pin for my trailer. Can i just replace teh 4 with a 7? | As a matter of fact you can. I recommend using part # 74682 because not only is it a 7-way, like you need, but it's also a 4-way in case...

Hi! I already have a trailer hitch, but no wiring harness on my 2011 BMW X3. Is there a way to install one, and what would it cost? Thanks! | There is definitely a trailer wiring harness for your 2011 BMW X3, the Curt Powered Tail Light...

Hello, I was wiring up my trailer and it seems everything is working great. Until I have my headlights turned on, and if I were to signal left or have my hazards on.. my left side tail light on my trailer stays constantly lit up and doesn’t...

I need a BT 150 Hub with L44649 bearings for a 5 on 4.5inch 12inch wheels Is this the one? These are the numbers one the existing hubs and bearings I need to replace. Thanks | You chose the correct hub for the dimensions you said you need....