!Outback Wagon  x   >   !Via Motorhome  x   >   !Carnival  x   >   1983  x   >  

83 chevy van B10 no brake or turn signal on left side | First thing you should do at this point is test the 4-way of the wiring harness with a circuit tester part # PTW2993 for voltage on all of the right pins when the taillight signals are...

Hello, I am looking for the driver and passenger side weldment attachment for a StowMaster 5000 to fit a 1983 Chevy K10. | In order to use the Roadmaster StowMaster Tow Bar part # RM-501 on a 1983 Chevrolet C/K Series Pickup you'll need the...

I have a question about my 1983 ford ranger when I look at the wires I saw two light bulb sockets should I splice the wiring harness to the second wire on both lights | You will need to use a circuit tester like the Circuit Tester Kit, item...

What wiring kit/harness/parts would I need to wire up my 1983 Jeep CJ7 to pull a small trailer with electric brakes? The trailer has a 7 pin hookup. Thanks. | You will need to start with a 4-way (if you do not have one). For that you would want...

Fey/westin 21000 rear bumper. I just watched the install video for this bumper, are there only two brackets holding this bumper on? my truck has four brackets | The Westin Fey Diamondstep Rear Bumper with Custom Installation Kit # 21000-92230...

Can I put 4.80-12 tires on it. hard to find 145R12c Also looking for directions on replacing lifter arm. Thanks | While a 4.80-12 size tire would fit because it is smaller, I recommend sticking with your 145R12 tire size (which is also known...

Do you make a wiring kit for a 1993 Chevy Blazer S-10 4X4 | Yes, there are wiring kits available for a 1993 Chevrolet Blazer 4x4. I assume you are looking for a trailer wiring harness. If this is the case, then I recommend the Curt T-Connector...

Have a 1983 F-100 that measures 37 1/2inch between the rails. Is the Curt 14001 the correct width for that installation? Thanks | When measuring the frame width on a vehicle, you will need to measure from the outside of one frame rail to the...

reciver addapter can i put a rack in this to carry fire wod | It sounds like you are referring to the RV Bumper 2 Inch Trailer Hitch Receiver # S64025. This particular bumper hitch is designed to be used with hitch-mounted bike racks and is...

Item 75082, what is distance C/L receiver to frame mounting. | Are you looking for distance from mounting location to bottom of hitch opening, top? I am not sure what you mean by C/L. | Bottom of receiver opening will work.. C/L means center...

How do you connect 4 12 volt batteries to a 1983 wanderlodge bus | There are two different ways that you can attach the four 12 volt batteries to your 1983 Blue Bird Wanderlodge. You can attach them in series or parallel. Attaching the batteries...

Wondering what the diameter is of the actual outside flange. I am hoping it will cover an existing hole | I have attached a photo of the Camco RV Drain Hose, part # CAM37420 for you. This drain hose features a Polypropylene trap on one end...

Will this part work with a blue ox tow bar. | The Demco base plate kit part # DM9518112 can be used with a Blue Ox tow bar but you have to use the adapter # DM9523034. |

Hi, Im stumped on this one. I have a 4 way flat wired to my truck, 1983 F-150. The brake lights work. The running lights work. However, the turn signals with a trailer hooked up, it acts as if a bulb is burned out. It will blink, but extremely...

Looking for baby moon hubcaps for my 1983 Jeep J10. Wheels are 15 with 6x5.5 lug pattern. Would you happen to have anything? Thanks. | We have a few baby moon hubcaps designed for 15" wheels and 6-lug bolt patterns: - Americana Baby Moon...

Your site lists my Bluebird Wanderlodge in the choose vehicle box, which most sites dont have a listing for. Im hoping this means there us a plug-in adapter for my coach? | Sounds like you are trying to wire a brake controller to your 1983 Bluebird...

Where is this jack produced? | The Curt jack part # C28304 is made in China. We do have a similar rated and style jack, the Dutton-Lainson part # DL22683, that is made here in the US. This jack has the same 2,000 pound capacity and 15 inches...

Will the Rola Cargo Carrier, Part # 59109 Provide Enough Room to Access Rear Door and fully open it? I have a 2001 Mazda MPV dx | Unfortunately, the only hitch available for your van has a 1-1/4" receiver. The Rola Enclosed Cargo # 59109 will...

I restored an 83 CJ7 and changed the color. I want to upgrade to these oversized polished hardware. Will it cover the original hinge footprint? Im concerned that if it does not the paint under would not match the existing paint. | The Rampage...

Hi! We have a GMC/Chevrolet motorhome built on a truck base, built in 1983. We would like to know if it is possible to put a towbar on the back of this, to tow a trailer with a boat on it. Can you tell me whether this is possible and what specs...

I am looking for 16” 8 on 6.5 steel dually wheels lug centered for a 1983 E350 motorhome front end | The Vesper Steel Dual Trailer Wheel # TA56FR will work for your 1983 E350 Motorhome. The wheel is a sturdy steel wheel that has 4 hand holds....

Can I install a gooseneck trailer hitch on my 1983 Chevy C20, also what is your recommendation thank you. | You can indeed install a gooseneck hitch on a 1983 Chevy 3/4 ton C-Series truck. B&W offers a compatible Turnover Ball gooseneck hitch...

I have a 1983 Ford F250 in which I am going to hopefully install a vehicle this wiring so that I can tow my Trailer. The Trailer has a Flat 4 pole connector, I see that this item Plugs into a Plug? I been under my vehicle and I have never...

How much drilling is required to install this on my 83 c10 longbed? | The Curt Hitch part # 13028 that you referenced is confirmed to fit your 1983 Chevy C-10. You will need to drill 6 holes to install all of the included mounting bolts for...