Is There a Trailer Hitch Available for the 1987 Ford Crown Victoria
Will this part fit a1987 ford crown Victoria or do you have to drill some holes ? part # is 13707 | I have a solution for you, but the Curt # 13707 is not a confirmed fit on your 1987 Ford Crown Victoria. Instead you'll want to use the Draw-Tite...
Correct Ball Mount for a 1995 Buick Riviera
I purchased a drawtite hitch for a 1995 buick Riviera and I already had a draw bar ballmount and I am unable to make it fit. is this design have a tappered draw opening. and if so what ballmount will work for the class 2hitch | I am not sure...
The Curt 2 Inch Class III Hitch, # 13707, On A 1999 Ford Crown Victoria Seems Too Low To The Ground
I purchased this part (13707) for my 1999 Crown Victoria and the receiver seems to low to the ground. In fact, the hitch is some 9 inches from the ground on an empty gas tank. Do you have any suggestions on this? Is this simply a problem...
Will My 2001 Ford Crown Victoria Require Modifications to Install a Trailer Hitch
I have a 2001 crown victoria with dual exhaust. It appears that exhaust modification is required for all trailer hitches you sell. What modifications are necessary? | Modifications to the exhaust are only needed on 2003 and later model years....
How to Determine Necessary Rise of a Ball Mount to Tow a Trailer Level
I recently purchased a wiring kit and a hitch receiver from etrailer.com, Curt part # 13707. I currently have this fitted correctly as shown in the etrailer video, and have installed a CURT 6inch rise 8inch draw bar onto the receiver with...
How Many Catalytic Converters Does 2005 Ford Crown Victoria Have
How many cats does a 2005 crown vic with a 4.6 v8 have 4 or 2 Ive been told it should have 4 two in front two kinda hidden by exhaust. | From what I found in my research, your 2005 Ford Crown Vic will have 4 catalytic converters, two per side....
7-Way Kit and Brake Controller Recommendation for 2007 Ford Crown Victoria
I have a 2007 crown Vic with a 4 way flat trailer plug can you recommend me products to make it adapt to a 7 pin I also need a brake controller thank you | You would need to convert the 4-way to a 7-way so that you can install the brake controller....
Replacement Hardware Kit For Mounting Class III Trailer Hitch Receiver On a 2011 Ford Crown Victoria
Hello, I recently purchased a Class 3 Trailer Hitch Curt or Reese, I cant remember which from a friend for my 2011 Ford Crown Victoria Police modeld. It did not come with hardware or any installation kit. Ive installed one before on a previous...
Weight Distribution Recommendation for a 2003 Ford Crown Victoria and 4k Travel Trailer
I am using a ford crown victoria to pull a 1994 19foot travel trailer weighing 4,000 lbs and has about 400lbs of tongue weight. The hitch is fairly low on the car so will this help with ground clearance issues? I was also going to install one...
Suspension Enhancement for a 2000 Ford Crown Victoria
i just got pulled over by a cop. because the trunk is very low . i told him its empty. he said get it fixed. help what should i do i love my car. i told him its an old car. he said fix it. | I did not know that having a sagging back end was...
Trailer Wiring Harness Recommendation for 2011 Ford Crown Victoria
Hi All, my name is Ron ... Does the 55326 work for a 2011 Ford Crown Victoria? Please let me know - I purchased the bundle from you trailer is 13707, btw. Thanks! | For your 2011 Ford Crown Victoria we have universal trailer wiring harnesses...
Does Draw Tite Trailer Hitch 41116 Fit 1999 Mercury Grand Marquis
I want to install this hitch on a 1999 Merc Grand Marquis. What else to I need ? Will I need wiring for lights ? | The Draw Tite hitch part # 41116 is a confirmed fit for your 1996 Mercury Grand Marquis. For a ball mount you'd need the part...
Installation of a Derale Transmission Cooler on a 03 Ford Crown Victoria
Do you have specific instructions for installing on my Ford. How difficult and how long? | Installation instructions for transmission coolers are pretty universal, but there are some variances between different vehicles. With that being said,...
Powered Trailer Wiring Harness that Fits 2007 Ford Crown Victoria
Can this module be used on a vehicle that is already a 2 wire system? I have a 2007 ford crown Victoria and I use want to use it for the powered taillight part. | We have a trailer wiring kit that was confirmed as a fit for your 2007 Ford Crown...
Trailer Wiring Recommendation for a 2004 Ford Crown Victoria
WHERE CAN I FIND A PLUG N CONNECTORS FOR MY TRAILER HITCH FOR A 2004 CROWN VICTORIA POLICE INTERCEPTOR | The only option we have for trailer wiring for your 2004 Ford Crown Victoria is a hardwire option like part # 46255. Or if you didn't want...
Are the Catalytic Converters Different for a 2001 Ford Crown Victoria Police Interceptor
Will the whole catalytic converters and pipe fix the same off a base crown vic fit on a crown vic police inter.. | I am not entirely sure I understand what you are asking but the catalytic converters are the same for both the base and police...
Trailer Wiring Harness for 2003 Ford Crown Victoria P71
Will this wiring harness work on my 2003 Ford crown victoria p71? | For your 2003 Ford Crown Victoria P71, which is the Police Interceptor model, you will need the Hopkins Universal Install Harness # 46255. This hardwire kit includes everything...
Trailer Hitch Fit for 2011 Ford Crown Victoria
Is the curt hitch # C12130 going to fit on my 2011 ford crown Victoria. this is the last year ford made this car. | The Curt Trailer Hitch # C12130 has been determined to fit the 2011 Ford Crown Victoria. I have attached links to our hitch...
Parts Needed to Install a Brake Controller in a 2002 Ford Crown Victoria
I just bought a Scamp 13foot camp trailer. My tow vehicle will be a Crown Vic 2002. They recommend a Tekonsha 9030 brake controller and a Bargman 6 spades with 1 center pin. Do you recommend these items and do you have any video of the installation?...
How to Find Brake Switch Circuit for 2011 Ford Crown Victoria for Brake Controller Install
color wire for brake controller | I wish I could tell you which specific wire color you'd need to find on your 2011 Ford Crown Victoria but we haven't had the chance to install a brake controller on it so what you'll need to do is use a circuit...
How to Order Replacement Mounting Hardware for Curt Trailer Hitch 13707
Hello I have a 2010 CVPI and hate to say I have the receiver hitch already. Im in need of the mounting hardware for Hitch #13707, is it possible to get this hardware? I have not an issue paying for it, just let me know. Again thank U for your...
Trailer Hitch and Wiring Recommendations for a 2003 Ford Crown Victoria with Dual Exhaust
I have a 2003 Crown Victoria with dual exhausts, and I was confused on which hitch to purchased .I read on the towing capacity which is 3000 lbs with 10 to 15 on the tongue weight. We would like a trailer light hook up as well and was wondering...
Dimensions of BP08-070 Replacement Manual Brake Adjuster Spring
What are the dimensions of the coiled section.of this spring? Im looking for a replacement for a 1959 Shasta electric drum brake manual adjuster. It has 2 springs per assembly. the current spring 4inch overall, and the coiled section is approx...
Are Inflation Valves Included with the AirLift 1000 Air Helper Springs for a 1995 Crown Victoria
Is there a airbags valve that I can go to a air pump and pump air in it on a 95 crown Vic for the airbags suspension | Yes, the AirLift 1000 Air Helper Springs, # AL60798, do come with inflation valves so you can fill the air bags at the location...
Filter Your Search
Contact and Help