!Liberty Travel Trailer  x   >   !Accord  x   >   !Arctic Fox Travel Trailer  x   >   M-3 and Associates  x   >  

how install an Enclosed Trailer Ramp Spring - Dual, 96inch Wide. the instructions arent really helpful | The installation instructions for the Ramp Spring part # CB250D96SHD are recommended for individuals who have experience winding torsion...

I am looking for a Rear ramp door lifting winch. I have seen them at the races and the older I get the more I want one. Do you sell them? | The ramp doors will use a spring system like # CB250D96SHD. Then you can use a winch like Bulldog Winch...

I am building a custom trailer with the rear ramp door being 7 foot tall and 66inch wide. I am expecting it to be heavy, so I was/am looking at the ERS160D96 due to its weight capacity. I am wondering what is the minimum width this model will...

Ramp assist my toyhauler ramp is to heavy to lift | I'd recommend a heavy duty ramp spring like part # CB250D96SHD. The unit is 96 inches wide, but could be cut down to a minimum of 80 inches if needed. It's recommended that these springs be...

Ramp Door Spring Assembly ? My Ramp Door weight is around 125 to 130 lbs. using a bath room scale and the Door opening is 88inch wide. Would 362SA8207 be the correct assembly for my door ? Can it be narrowed down to 88inch ? | The 120-LB...

Hi, Im looking to convert a double door to a ramp door on a 6x12 trailer. Not really sure how to go about this. Is the easiest solution to buy a ramp door? Do you sell them? Or is it possible to use the double doors as the ramp? Thanks,...

I am needing 2 cables for the ramp door to my momentum,. do you sell them, as I need them for my patio to hold ramp parallel to ground. hold it up like a patio. | We do have cables but they are not specific to a ramp door on your Momentum, they...

My dad backed a lawnmower over his enclosed trailers door cable and broke the cable loose and broke the pulley attached to the top spring mechanism. Do you guys sell just the pulley from this setup on your site? CB250D96SHD | The Replacement...

Can you help me figure out how to calculate spring size needed on a trailer door that has springs overhead | In order to measure the size of spring # CB250D96SHD your trailer ramp door needs, you'll want to take these measurements: Measure...

I am interested in purchasing only the spring for a 7ft. trailer. Single or double with capacity of 150lb or more. Do you sell the spring by itself and how much is it. Or can you let me know how to get it. Thank you | It sounds like you're...

Could I please get a copy of the installation instructions for the #CAB1-8CB150 cables if you have them. Thank you | The installation instructions for this product are recommended for individuals who have experience winding torsion springs....

Can you tell me what size spring assist assembly do I need for a 6x12 enclosed trailer? Thanks | When selecting ramp springs for a trailer ramp, you will want to know the diameter of your hinge pin and how much space you have available in the...

I am building ramps for my box truck and will require springs to help lift them. I figure one ramp is approx #800 and the second is #300. Ramp 1 is 60” wide and 10ft long, the second is 34” wide and and 10ft long. The ramps are bifold. What...

I would like to know if I can cut it down to 81 inches to work on my trailer I have a 2005 haulmark trailer 7x14 Thank you | Yes, you could trim down the ends of the Enclosed Trailer Ramp Spring # CB250D96SHD to take it down to 80 inches minimum....

Can you send me info on how this light wires. I do not see connections in the pictures. M337FR 120volt | The wiring of the Exterior LED Utility Light # M337FR that you referenced is pretty basic. It has three wires, one for power, one for ground,...

I am looking at ramp door spring #M394FR for my enclosed snowmobile trailer. It currently doesnt have a roller spring and I would like to add one. I see the measurement says its 4 3/4 but what I need to know is what size is the mounting bracket...

will 2 EZ gate tailgate lift assist work on back door ? 6 x 12 enclosed steel trailer | It is best to use the Conventional Ramp Door Spring for 6' Wide Enclosed Trailer # M364FR. This will fit a rear door 37-1/2" to 67-5/8" wide. The EZ Gate...

rack em tailgate lift assist. Can this be installed on a horse trailer ramp? | If you have an interior rail to attach to, you could uses the Rack'Em Double Barrel Utility Trailer Tailgate Lift Assist w/ Chain - 200 lbs # RA-27C. The only thing...

I have an 8foot x 8, 240 pound door and was wondering how far out on the door do I need to go to anchor the assist cables, if I use the 96inch 160# system? Thank you for your time. | You'll want to anchor the straps that the Enclosed Trailer...

Do you make a spring assist for a 8 and a half wide trailer | When installing a spring assist on your 8.5 foot wide trailer I recommend The Conventional Ramp Door Spring for 8 foot Wide Enclosed Trailer - Dual Spring - 250-lb Capacity # CB250D96SHD....

Of all the information on the ramp spring assemblies why cant I find a product weight or shipping weight. Seems to me it would be valuable information for installation. | Though I can't give you a reason why, I can tell you that the Enclosed...

What is the wire size of this setup? | The Conventional Ramp Door Spring for 8 foot Wide Enclosed Trailer # ERS160D96 cable is 174 inches long by 1/8 inch diameter. The spring has a sturdy steel construction and has a spring capacity up to...

I have a 2004 28foot Vintage Outlaw call hauler. The specs state it is 96inch wide. We need a new ramp door spring. Can you advise me which would work best and availability? Are their installation instructions available? | For a 96 inch...

LOOKING TO SEE WHAT ALL COMES IN THIS KIT DOES CABLES COME WITH IT AS THEY ARE SHOWED IN PICS | The Conventional Ramp Door Spring for 7' Wide Enclosed Trailer, # ERS120D81 includes the spring assembly and cables. |