Would Dutton-Lainson DL21741 Roller Bunks Contact Keel of Boat
I have a 1989 z-loader trailer, does the aft roller touch the keel of the boat ? | The # DL21741 Deluxe Roller Bunk would bolt to the bunk boards, which are designed to support the sides of the boat, not the keel. Therefore, the aft portion...
Available Lengths of Boat Trailer Roller Bunks
I live and work in Cape Coral FL, Ive owned a dock and boatlift company for 15 years. I get asked a lot about putting roller bunks on boat lifts due to our winter low tides. Do you make them 12, 14, or 16foot ? Cost ? Thank you | We offer...
Replacement for Old Dutton-Lainson 800 Pound Tongue Jack
I have a Dutton Lainson sidewind jack label # 203871A rated for 800 lbs. What model replacement handle would fit this jack. It appears to be manufactured before 1996. Thanks | I spoke with my contact over at Dutton-Lainson and found out...
How To Choose The Correct Electric Winch For A Boat Trailer
Im confused! I thought the lb rating on winches was to determine appropriate pulling rate. For example, if my pontoon boat not including trailer weighs 2,500 lbs, I should look for an electric winch with at least 3,000 lb line weight. I also...
Recommended Hand-Brake Winch for 1/4 inch 45-50 foot Cable
looking for a hand winch with break that will accept up to 1/4 cable and mount onto a 45-50foot telescoping ham radio heavy tower to raise the tower up/ down. Need to winches. One for each tower. Already have spool of cable. | The Dutton-Lainson...
Davit Winch Recommendation for Davitmaster 1850
I live in Bermuda, and currently have a Davitmaster 1850 lb seawall mount davit on an exposed dock, which I use to launch a small dinghy with an outboard total weight around 600-700 lb by lowering it about 6 feet to the water. Each winter the...
Boat Trailer Roller Bunk Replacement Rubber Wheels
I have a pair of these bunk rollers purchased 1 1/2 years ago. I am far from happy with the rubbers on these channels. I trailer my boat approximately 20 times a year. The rubbers are very soft and are peeling. Ive had to try to repair 4 of...
Typical Spring Deflection of Torsion Trailer Axles
How do I determine start and articulation of torsion axles? For a boat trailer, would like 3500lbs axles, 2 axles | Torsion axles can have different spindles with varying geometry. The specific spindle installed will have a specific range of...
What is Amperage Draw of Dutton-Lainson StrongArm Electric Winch # DL25500
I know it draws a lot of juice - is it near 70 amp? Using this for my boat on a very shallow water launch - Is there any kind of fuse or circuit breaker built in, or if not recommended? Loading is only half of the problem - is there a way...
Hello Etrailer.com, I have been looking at your winches and would like to buy one. I have a unique need for raising and lowering my 55 lb kayak to the river that is 75 feet down a 45 degree slope. I can currently use a 75 foot rope and gloves....
Can the Fulton 3205 Be Used with a Polyester Strap Instead of Wire Rope
Can I use a strap instead of cable on a Fulton 3205 if so what width | I have a solution for you, but the # F142421 is designed only to be used with cable. Instead you'll want to use the Dutton-Lainson Hand Winch - TUFFPLATE Finish - 2 Speed...
Dimensions of the Parts Included in the Dutton Lainson Miter Gear Kit # DL22439
Hello A friend of mine just bought an old truck camper and one of the jacks has a bad miter gear set. there are no markings at all on the jacks at all. im having a difficult time finding replacement gears as im sure you know they are all prapriataory. I...
Worm Gear Winch Recommendation for Hoisting a 150 lb Float
I need to lift a 150 lb float from the water 8 feet up to the under side of my dock where it hanges. I presently am lifting it by hand but I am 74 years old and a winch on each side will really help. I want to ratchet the float up and ratch...
Bunk Roller Recommendations for a Boat Trailer to Help Boat Load on Trailer
I have a Rivers and Streams 14 foot trailer sold locally by Fleet Farm here in MN, It has two four foot bunk slides that I want to upgrade to rollers, as it is too difficult to slide on the bunks. I am looking at the item# DL21740 for...
Will Fulton F2 1,600 Pound Winch Fit Dutton-Lainson Winch Mounting Plate DL24059
Will a F2 winch work? It a hand winch. Thanks | The Dutton-Lainson winch mounting plate # DL24059 has the top 2 holes spaced 2-1/2 inches apart on center and the third hole in the middle is down 3 inches from the center line between...
Lock Recommendation for Fitting Pin on Trigger Latch Coupler
Whats the radius of the locking hole on a trailer coupler? Im looking for a secure lock, and I have a padlock in mind, but the shackle dimensions do vary. Please advise. | Sounds like you are looking for a lock for the trigger latch of your...
USA Made Trailer Axle, Wheel/Tires, and Trailer Jack for 3,500 lb Trailer Axle
Good morning Wanted to use the Timbren system but the cost . Also where is this system built. . Looking for a 3500lb axle with brakes an all the hanger parts including springs of coarse. 5 hole wheel 14 will be using 2inch wide...
Mounting Post Recommendation for Winching Boat Trailer Out of Water
Im looking at dl14881 3,500lb braking winch to haul my boats onto the grass each fall. What kind of post, how high and how deep, do I need? | When determining the mounting height for installing a winch you want to choose a height that will...
Boat Winch Recommendation for a 4,500 lb Boat
Trailer Winch capacity needed to load 4500 lb boat from boat ramp What capacity winch is needed? | When it comes to choosing a winch for a boat trailer, there are a few general rules we can use. The boat-size-to-winch capacity is generally...
Can Winch be Anchored to Concrete Floor
Hi Is there a winch that can be drilled into concrete to put on my boat ramp that is going to be used for a Sea Doo? Many thanks | We do not offer them, but there are winch mounting plates that are designed to anchor into concrete that you...
Replacement Parts for Dutton Lainson Trailer Jack
I need a Dutton-liaison jack with a model#203960B. Do you have this or a replacement for this. | We do offer both replacement parts and complete Dutton Lainson trailer jacks. All complete jacks can be view by clicking on the linked page. All...
How to Determine if a Dutton-Lainson Swivel Jack Will Fit a Demco Tow Dolly
I have a Demco SS Kar Kaddy tow dolly which has a swivel jack attached four bolts to a welded on bracket. Do you know if the holes on this jack will line up with the one on the Kar Kaddy | Dutton-Lainson jack # DL22300 is a potential fit for...
Mounting Bracket for Winch Quick-Connect Wiring
I am looking for a waterproof/resistant mount for an Anderson SB50 connector. I am using it to connector power to my boat winch when in use. I dont want it to hang off of the bumper because Im concerned that it might short of it comes in contact...
Does Dutton Lainson Worm Gear Winch DL11011 Require Cable Fastener
I am planning to use the DL 11011 winch to hoist a 150 LB. personal pontoon boat up 20’ to the ceiling of my garage. I plan to use 5/16” synthetic double braid rope on the drum. Is there any real need to use the DL24361cable fastener to attach...
Filter Your Search
Contact and Help