!Eagle Super Lite Travel Trailer  x   >   !Plymouth  x   >   !Envoy  x   >   TRC  x   >  

Greetings, Regarding the: Nosing Edge Trim - Enclosed Trailer - 93-1/2 Long x 1 Tall x 3/16 Deep - Aluminum Item # 362555-955 Is the 3/16” dimension the overall depth of the trim piece or is it just the inside depth of the nosing edge only...

Hi...is this bendable? building a tear trailer. | The Angle Trim for Enclosed Trailer # 36290-955 being made of aluminum is easily bendable if done correctly. To bend this around a radius you will need to make relief cuts into the radius so...

I saw an article, its titled avaialblilty of a floor escape hatch for enclosed cargo trailer. I see the hinge, the handle and the suggested lock... But what is the copper looking stuff bordering the hatch door and the opening. What is it for?...

The trim on my trailer measures at 1 3/8. Would this be the replacement for that. It looks identical, but does not measure 1 1/2. thanks a lot. | Yes, since your current trim is only 1/8" smaller than the Even Rub Rail Trim for Enclosed Trailer...

I would line to purchase a new installation ramp spring for my cargo trailer. The trailer is 72” wide and I would like to have a system with the adjustable width. Can you help me out? | For a 6' wide trailer we have the 120lb capacity # 362SA6...

How long are the cables | The length of the cables that come with the ramp spring part # 362SA8 is 150 inches. |

What item d seal # fits 2018 3270rs bighorn fifth wheel slide out | Something like the D-Shaped Rubber Seal for Enclosed Trailer # 362WS1463-25 might work but I'll need you to take some measurements for the part your referring to. This rubber...

do you have available trailer exterior door h channel that is 1 1/8 wide. 1 seems to be standard, but i need wider | I do have an option for you but we only offer the H-Channel for Enclosed Trailers part # 36281-955 is one size, 93-1/2" long...

I have an enclosed trailer with a ramp door on the side. The opening is 45”. I have a drum max load of 320 lbs. The pipe diameter is 1” and is 46” long. How do I weigh the door to figure out the spring needed? | To determine the correct weight...

# 362SW61 Is this part # still available???? Ive got a cellar door that is flat on a concrete floor so far I got a Hernia lifting the dang door, ANY IDEAS! Weight 50-75 LBS 1/2 plywood | The 120-lb Capacity Self-Winding Ramp Door Spring...

I’m struggling to find the correct replacement trim for my trailer is there anyway you can help me? | Brendon, you'd need to measure your current rail length and width and take note of what the shape is. For instance, if you measured your current...

We have a 2015 Vengeance The rear ramp door is very heavy. We have to lower it several times a day to let our older dog out. Any ideas to lighten the load? | We do offer a ramp spring that would work for you. According to my research, your...

Hi what product do you recommend to replace the ramp door seal on my Haulmark 7X14 enclosed trailer? The current seal had seen better days. Thanks | Get this D-Shaped Rubber Seal # 362WS1463-25 for your Haulmark 7'x14' enclosed trailer. This...

I see that you have Torsion spring kits for 80 lb and 120 lbs doors. My door is 95 lbs. Which kit do I choose? Will the 120 lb spring have a tendency to lift the door when fully open or be will it be harder to operate and pull open? Will...

What is the base opening? | The C-Channel for Enclosed Trailer # 362213-955 has an opening of 1.027". I have included an image below with all the dimensions for this item. |

Can the gorilla lift be installed on an enclosed trailer? | I have a solution for you but the Gorilla Lift item # GL1 you referenced only works on utility trailers with raised bed rails. To help raise the ramp door of an enclosed trailer you...

Hi I was looking at your 1inch c channel aluminum trim, it says its 1 tall and 1 deep, which sides are you classifying as the tall and which side is the deep? I guess my question is how wide is the channel itself? I have a 1inch piece of foam...

Ramp Door Spring Assembly ? My Ramp Door weight is around 125 to 130 lbs. using a bath room scale and the Door opening is 88inch wide. Would 362SA8207 be the correct assembly for my door ? Can it be narrowed down to 88inch ? | The 120-LB...

Awning Rail Extrusion for RV or Enclosed Trailer - Aluminum - 93-1. I understand the cord hole is 1/2 but was is the size of the cord hole slot? | The opening of the slot on the Awning Rail Extrusion part # 36287-955 is 1/4 inch and like you...

I have a 2018 Lance 2375 TT. I would like to install a slide awning. I did measure flange to flange on the slide. It is 90 inches. Also, when Lance built the trailer, they installed a combo roof drip rail, that has a groove for an awning to...

I have a Carson Racer enclosed trailer and I am in need of replacement door springs. Its a very heave door. What size springs come with your heavy duty,230lb, door spring kit? Just want to make sure I purchase the right springs. Thank You...

Looking for a spring to fit a 5/8inch od shaft. Going on a ramp 44inch wide x 69inch long. | The best ramp assist spring recommendation I can make for you would be the Enclosed Trailer Ramp Spring # 362SA7. Check out the review video I attached...

I am looking at converting a small enclosed trailer which currently has a swing door to a ramp door to make it easier to load my motorcycle. I know I will have to beef up the inside of the door for the increased weight. The door is 48inch wide....

I was wondering if there was any other lengths of this product available. I have a 7foot x 12foot v nose enclosed trailer that I need to redo some of the top trim. Fewer pieces the better. Thank you | The only length of the Top Rail Trim...