Result: Step Support

We typically recommend the part # PF775-BKT-2 as a way to support the steps of a plastic fender like your # F008575. | the mounting brackets I got the part number CE26098G-2 for these fenders F008575 are useless,...

The Fulton Plastic Fender with Top and Side Steps, # F008582, have molded in steps on each end and the top of the fender and are designed to be stepped on as long as the mounting hardware used is capable of supporting the weight that will be required. |

I have two questions: 1. Will the brackets support the two side steps of the fender as well as the top step? | I am looking at installing Fulton Fenders item # F008573 and mounting them with...

Does it require brackets to support the weight of stepping on it? Or...can you simply bolt the rear flange flush against the frame with spacers as required ? | Looking at the F008553 fender. 13 tire. Does it...

I am considering the Lippert Solid Step for my 2015 Keystone Raptor but there is currently a gas strut on the bottom of my RV door that ties to a floor pin in the existing entry threshold. about 3inch from the right side That existing door bottom strut helps manage the door in windy conditions and keeps it from banging on the RV exterior . |

They cannot be used as a step. I want to replace them with step fenders. | I have a 2020 NuCamp Boondock Edge TAG tear trailer. The tires are 15 inch ST235/75R15 LRC. The existing fenders attach to the...

Hi, Are these really strong enough for my 210 lb weight to stand on? Thanks | The 3 Fender # CE19502-2 is rated for weight of up to 300 lbs. You will need to make sure you have the appropriate brackets like # PF1135-BKT-2 to give you the needed...

You'll want to go this route rather than using L-brackets as L-brackets wouldn't provide enough support to allow the fender to be stepped on. I've linked to our selection of U-bolts. | What L brackets and mounting...

If you choose to install by drilling in the backing and mounting to the trailer frame in that location the fenders will work well but you will not be able to utilize the steps on the ends or top of the fender as the intended mounting brackets are what help support the weight in those locations. |

Hello, I am looking for brackets for mounting these fenders to my 3H x 1.5W frame? Also how wide is the mount brackets ? Since my spring mounts are 32 3/4inch apart outside . Thanks, | The mounting brackets you can use to attach the # CE19503-2...

I need a fender that fits that. My supports for the steps are four inches wide and eight inches out from trailer to end. | On the Redline Trailer Fenders - PF11X35W I need to know how far apart the mounting...

First, I would say if there is any question on the road worthiness of the trailer, take the steps to correct it. Better safe than sorry. Some trailers have wheels that are hub-centric, the wheel is centered on the hub using the center pilot holes. |

The Fulton Single Axle Trailer Fender with Top and Side Steps # F008585 is also available as a 2-pack # F008585-2 for your 1999 Escort WT18GA Boat Trailer. | 1999 Escort wt18ga trailer for Bayliner Capri boat. Looking to replace...

This will be the most effective first step to reduce sway but you can still add other aftermarket kits later on if you still find a need. | will this help my Pleasure-Way 2001 Dodge 350 van RV from wandering when passed by...

I attached a picture that shows that step of the instructions for this kit. The roller has to be removed so that the spring of the RAS can lay across the leaf spring like it needs to. | I know the standard duty RAS3611 is...

I went ahead and attached the steps from the installation manual for attaching the kit with your overland springs. | Hello, I own a 2020 Silverado 3500hd with a 3,700 cargo capacity. My vehicle has two overload leaf springs...

I have stepped down from an F-250 to an F-150 2019 Platinum Crew cab with 5.5foot box and noticed a considerable difference when towing my enclosed trailer. | I have stepped down from an F-250 to an F-150 2019 Platinum Crew...

I recommend the Plastic, Single-Axle Trailer Fender w/ Top and Side Steps # PF11X35W. If you want matching fenders, then you want # PF11X35W-2. | White plastic Whitney ligot for 14 inch Plastic fendre | We have white plastic...

The Fulton Single Axle Trailer Fender with Top Step - Black Plastic - 14" Wheels - Qty 1# F008554 is a great fender to replace what has broken on your current tow dolly. | At 10pm on a road in the middle of nowhere, the fender...

To take it a step further, you can also install the 2-Piece Polypropylene Trailer Vent for 3" Diameter Hole # WHMAV2-WAVT2 lower on the trailer to create a nice cross-wind, and help moderate the temperature. | Im looking to...

I am trying to avoid a weight distribution hitch due to the extra steps associated with hooking up the trailer. I would prefer to it on the hitch and go if that option is available via air bags. | I am looking for air bags...