Can Slide Topper Fit Right Next to Awning on RV
My question, have a 2023 keystone avalanche 302rs, on the one slide out there is a elec awning and I would like to be able to put a slide topper on that slide, is there a special bracket kit that will allow a slide with awning also mount a slide...
How To Find the Correct Landing Gear Legs for a 2012 Keystone Avalanche
replacement landing gear recommendation for a 2012 keystone avalanche 5th wheel | In order to find the correct replacement landing gear legs for a fifth wheel trailer I would need you to take two quick measurements of your existing landing gear...
Landing Gear Gear Box and Motor Replacement for 2011 Keystone Cougar Fifth Wheel
What parts/numbers to replace the landing gear motor and gear box on a 2011 Keystone Cougar | Keystone RVs use landing gear from Lippert so the correct gearbox and motor would be part # LG-179015 and then for a motor you'd want # LC142178. |
Troubleshooting Landing Gear Retracting Intermittently on 2010 Keystone Avalanche 5th Wheel
My 2010 Keystone avalanche landing gear will go up and then stop completely. After I wait a few seconds it will start working again but then stop. I replace the motor and it still doing the same thing | If your landing gear is acting up like...
Solution for 5th-Wheel-to-Gooseneck Adapter on 2022 Keystone Avalanche
I have a 18k road armor trailair kingpin box serial #s008970731. RPO # 0008418006. I would like to know what Reese air gooseneck box would fit. | Thank you for providing that information. According to Lippert, you have a 1621 pin box rated...
Is there an Angled Mounting Bracket for a Lippert Ground Control 3.0 Leveling System LC421484?
I have seen on Brinkley 5th wheel RV, that the Ground control 3.0 display panel is mounted in a plastic box that looks to be angled maybe 45 degrees, so that when you open the compartment door the face plate is more pointed towards the door....
TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear
We recently purchased a fifth wheel camper. I have mobility issues and need steps with a low rise. We have a keystone Avalanche | Most RV steps are going to have a drop/rise of about 8". The TorkLift GlowStep Revolution Scissor Steps w/ Landing...
Why Do The King Pin Plate Pivot Bolts On The Rota-Flex Pin Box Keep Coming Loose
I have a 2022 keystone avalanche with the lippert roto flex pin box. The two bolts that hold the cushion keep coming loose. I keep re tightening the bolts to 90-100 ft lbs. Any suggestions | The Trailair Rota-Flex 5th Wheel Pin Box # LC328330...
Troubleshooting Brake Shoe Wear on Dexter Nev-R-Adjust Brake Assemblies
My 5th wheel trailer has 12x2inch Dexter never adjust brake assemblies and Dexter brake drums. These brakes are the origional factory brakes and I have 30000 miles on them. All four wheels show identical ware but I have noticed something which...
Transmission Cooler Recommendation for a 1993 Dodge Ram
D13402 be the best for my truck | The Derale Stacked-Plate Transmission Cooler # D13402 that you referenced is an excellent choice for a transmission cooler, and as long as you have the room for it in front of your radiator for this cooler then...
Roof Mount for a Light Bar for a 1984 Dodge Ramcharger
I have a 84 ram charger an just purchased a straight 52inch light bar. Will this mount to the light bar mount | The main cross bar on the Carr light bar mount, # CARR210111, has 5/8 inch diameter holes and there are long slots to accommodate...
Replacement 7-Way Connector for the ETBC7
Hello, I purchased a ETBC7 kit a few years ago. Product has worked very well, but the square plastic has cracked. Is there a way to purchase a replacement one utilizing the same 7 pin round part. Is there another solution to the plastic...
Is The Aluminum Bearcat Trailer Wheel # LH97VR Lug-Centric Or Hub-Centric
Is this wheel lug centric or hub centric? | Hey Mark, The Aluminum Bearcat Trailer Wheel # LH97VR is centered on the wheel studs so it would be a lug-centric wheel. |
Is Drilling Required to Install JT's Strongarm Kit # LC191023
Is drilling into the frame required for the installation of the JTs Strong Arm system? | Yes, there will be drilling into the frame with the included self tapping screws to install the JT's Strongarm kit part # LC191023 that you referenced. |
Does Solera 16 Foot Black Fade Awning Roller Assembly Work With Dometic 9100 Awning Arms
I have 2020 keystone avalanche and need to replace roller on my 16 ft awning. The awning arms are in great shape. We have a Dometic 9100. Will this work with the arms from a Dometic 9100? | The Solera RV Awning Roller Assembly - 16' Wide - Black...
Correct Titan Chain Snow Tire Chains for 31x10.5-15
Will the TC3210 fit my 31x10.5R15? The 31x10.5R15 is close to a 265/75R15, which entailed says is the TC2221, however, other sites show smaller tire sizes for the TC2221. | Th correct Titan Chain Snow Tire Chains for Wide Base and Dual Tires...
Can Blue Ox Bolt-On Base Plate Bracket Kit be Installed at Different Measurement Than 21-1/8"
I have a 1982 Ram charger. After market bumper that will have to be beefed up. The installation instructions are pretty specific on measurements. How critical is it that I maintain the 21 1/8inch distance between the base plate inner bolt holes....
How to Pick Out Ball Mount for Trailer Hitch
Not sure what its called but its part of of the hitch. It is L shaped and slides in the receiver hitch. Need one soon! | Is it possible you are looking for a ball mount like the part # C45036. The ball mount platform is somewhat L-shaped. I...
Why Would Installing New Trailer Brakes Require More Brake Controller Voltage
Hello - just installed new brakes on my 2010 Keystone Laredo 5th wheel. Install was straight forward. One issue I have now is that the gain setting on my integrated trailer brake controller in my truck 2008 GMC Sierra 2500 needs 9.5 to engage...
Locating Replacement Hubs and Brake Assemblies for 2014 Keystone Cougar Trailer
I have a 2014 Keystone Cougar High Country, Model 333MKS. Which hub assembly is the correct one for my 5th wheel for the left rear wheel? I have had the bearing fail me 3 times in the past 2 years. I had to replace the hubthe first time, the...
Locking Pin Compatible with BWGNC4250 Gooseneck Coupler
It does not do any good for the coupler to lock to the ball if all you have to do is remove the entire coupler. The pin holding the coupler in the sleeve needs to be a locking pin. What would be your recommendation. I was looking at InfiniteRule...
Gooseneck Hitch For A 1980 Dodge W400 PowerWagon
Hei. Maybe I made å wrong question last time... I try again. I do not have the frame monted steel unitinch to be connected to the frame so å can attatch the towing ball. I dont know what you call it, but it is bolter to the frame so I can...
Picking Out Trailer Hub/Rotors for Dexter 7,000 lb Axle
I have a dexter 7000 lb axle I am not sure what stud diameter I have on the current drum brake. I am looking at the K2HR712D conversion kit. Do I need to confirm the stud size or can you confirm it off of the axle number. I am at work...
JT Strong Arm Stabilizer Kit Compatible with 2016 Keystone Sprinter 5th Wheel Trailer
I purchased the strong arm stablelizer for my 2016 keystone sprinter , got home and seen thst they are for a travel trailer.Can I make these work on my fifth wheel by making a bracket | The JT's Strong Arm Jack Stabilizer Kit for 5th Wheel RVs...
Filter Your Search
Contact and Help