!Designer Camper  x   >   !Prevost  x   >   Ultra-Fab Products  x   >  

Hello Im interested in this hitch for my camper. Please find the pics attached. I want to mount this to the 2inch x 4inch tubing that is welded underneath the main frame. The dimension in between the tubing is 69. The length of tube is 14. I...

Do you offer the replacement spring loaded plunger pin assembly for the bulldog 500170 jack? | According to my contact at Bulldog a replacement plunger pin assembly for their landing gear set # BD500170 is not offered as a separate replacement...

Hello, We have a 2014 Heartland Bighorn 3610RE and would like to have a bike rack installed. Can you let me know if Adjustable width trailer hitch receiver Code: 13703 would be the correct one for our fifth wheel? Thanks | Before attempting...

Do you have a good picture of the control panel for these jacks? Is it a two switch or a three switch panel? Is the panel itself made from aluminum, plastic, or some other material? Thanks. | I attached a picture of the switches for the Ultra-Fab...

Installation of UF48-979023 We have a 43.2foot Riverstone 5th wheel that we want to buy these rollers to prevent any tail drag damage to RV. We have a welder to do this...My question is, does the welder just weld the wheels on or do they have...

Hi How big a vent pipe can you fit inside the ultra fab solar vent and how much can the vent pipe stick above the roof before it would interfere with the fan? Thanks | The Ultra-Fab Solar-Powered Plumbing Vent # UF53-945001 has a bottom opening...

mounting holes on uf-38-944017are 21/4 am assuming that is the distance from edge of one hole to the edge of another?? Need something that fits 3inch center to center. | I went to our warehouse to measure this jack's mounting flange and it...

I have two question: first I have a 30 ft. tracer air that came with 30inch jacks on all four corners as typical. the empty weight of the trailer is about 7400 lbs. I have managed to bend the front two jacks one from a mishap with the weight...

I am looking for a bike rack for our camping trailer. It has a bumper mounted spare that tilts for access to rear storage that we use. Any suggestions? I worry the swagman around the spare mighty rack wont allow me to the spare down. | For...

I have a 2005 Keystone Everest that I need to replace the landing gear. What do you recommend? | In order to pick out a direct replacement for the landing gear on your trailer we would need to know the distance between the mounting brackets....

Im wondering if this Jack will fit and work on my Forest River EVO 2550? | I can tell you exactly what you need to know to find out if the the Lippert Components High-Speed Power Stabilizer Jack - Black Waterproof Switch Kit - 30" Lift # LC298707...

Can I use this support for the slide | We have just what you are looking for. These supports will signifcantly reduce bounce and movement for slide outs. Ultra-Fab has two sizes of slide out supports - sold in quantities of 2 per package. The...

I have a 2018 endurance by Dutchman will these jacks work | As long as your existing landing gear have their weld stops in the standard positions as shown in the linked photo (15-1/2 inside to inside and 17-1/2 outside to outside) and the outer...

Thank you for your previous assistance. Which weight tongue jack do you recommend? I am a senior and need one that is very reliable. Thank you. | I think the best value for an A-frame tongue jack is the Stromberg Carlson # SC63VR which is rated...

Hello, I am replying to someone elses question. I bought the Ultra Fab RV carrier as did this customer. But my 2006 Honda Reflex NSS250 doesnt appear to fit due to the front brake disk. I was totally broken heartd. I went back to this FAQ to...

I have a 2014 camplite 14dbs. I have the jacks that came from the factory. Would like to have mounted jacks on camper that I can do both. | I have a solution for you but using any type of stabilizer jack to lift your camper is a no go. They...

We have the referenced 5th wheel and would like to carry our Vespa 150 LXi on a carrier behind it. The trailer came with a factory-installed receiver hitch, 2, and is rated at 350 lbs tongue weight, 3500lbs. tow capacity. Is it advisable to...

Hi - Im looking to get a spare tire for my travel trailer. Travel Trailer: 2021 Heartland 27RKS ST225/75/R15 6 bolt pattern What do you recommend for a spare? also, a bumper carrier for the travel trailer Thanks | For your 2021 Heartland...

I have a 2000 Alpenlite 32RK Limited 5th wheel that I want to add a 2inch Class III receiver to carry bicycles. I was looking at Curt #C13701 or Curt #C13703 on your site. Will they work on my trailer. If not what do you recommend. Thanks...

Do you have a rear hitch for a 2015FL Montana that could pull a 2000 pull load | We have several possible hitch options for your 2015 Montana. I have included a couple of links. One of them is to the frame mounted RV trailer hitches that we...

Our travel trailer spare tire is currently stored in the trailer under the bed. This limits the trailers capacity to carry the gear we need. We are looking for a bike rack that will hold mount the trailer spare tire not a bike rack that will...

2016 Holiday Rambler Ambassador 38ft diesel pusher, 5000lb tow capacity, 500lb tongue from a Class lll receiver. Have attached a Curt Dual hitch extender to pull Master Tow dolly with 2015 Honda Civic Sean, and a bicycle rack on the upper receiver...

I am looking for the bolts to attach the hitch to my rv bumper | The hardware is included with Buyers Products RV Universal Receiver Hitch # 3371804060, however if you have misplaced or damaged the U bolts, you can use the Replacement U-Bolt...

Ive measured the outside of my I frame from the outside of the bottom of both sides and it measures 77. The bottom lip of the frame is approximately 1 1/4 guessing it the same on each side of the beam. Im not sure how wide the I frame body...