Would the Load Stops for Thule Ladder Rack and Aeroblade Load Bars # 753-3761 Other Brand Aerobars

Question

Question:

I have this rack system: The rail is 7/8inch inside with a 1/4inch slot. Will these fit?

asked by: Don O

0

Expert Reply:

I spoke with my contact at Thule and the first thing she said is that the Load Stops part # 753-3761 that you referenced have only been tested to fit the Thule Aeroblade cross bars.

However, the T-bolts of the # 753-3761 are .75 inches square which would fit well in the slot you have on your bars that measures .875 of an inch.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I sure can Bob and thanks for the information! Since you have a Lippert 3,500 lbs axle you'll be able to use the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles item #AKHD-545-35-EZ-K, you were looking at. These have a 5 on 4-1/2 lug nut…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hey Drake, thanks for reaching out! The Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs #F2709 will work directly with the Firestone Air Command Heavy Duty Air Compressor Kit #F96VV to fill your tires with no other parts needed.…

view full answer...

Answer 4

It looks like you ordered both from us today to use with your Carrier lower vent assembly. The heat strip will work with the Advent but if I am being perfectly honest a lot of times these mixed brand AC Unit solutions don't work as consistently…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Hey Paul, great question! The etrailer Ladder Rack #e78FV and Erickson Ladder Rack #EM07707 are very similar, but the value trade-off between the two is huge. One thing you'll notice is we have a lifetime warranty on our rack versus the typical…

view full answer...

Answer 8

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Would the Load Stops for Thule Ladder Rack and Aeroblade Load Bars # 753-3761 Other Brand Aerobars

Product Page this Question was Asked From

Continue Researching