Length of Barrel of # UWSLOCKCH502 Replacement Lock Cylinder

Question

Question:

I am looking for one that is only 9/16inch from the bottom of the head to the bottom of the entire assembly.

asked by: Keith

0

Expert Reply:

From the rear of the lock facing to the bottom of the assembly, the # UWSLOCKCH502 Replacement Lock Cylinder measures 13/16 of an inch, as you can see in the photo I've edited for you. I'm sorry to say that we don't carry a replacement lock cylinder whose barrel matches the length you're looking for.

expert reply by: Mike L

0

click to enlarge

Answer 1

There are several different lock and key replacements for UWS toolboxes and each one is different from the next. There is a chance you could end up with the same lock and key that you already have on the box but you would just need to order a…

view full answer...

Answer 2

I did confirm that the replacement lock cores for UWS toolboxes like the #UWSLOCKCH508 does in fact use the rivet you referred to, but these are the only locks we've got that are confirmed to work with a UWS toolbox. We also added this photo to…

view full answer...

Answer 3

Key codes for UWS toolboxes usually include the letter prefix CH. Please refer to the photo that shows where to find this on the face of the lock. This photo happens to show a lock code CH510. I tried both of the codes you gave but neither seems to…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Length of Barrel of # UWSLOCKCH502 Replacement Lock Cylinder

Product Page this Question was Asked From

Continue Researching