Electric Jack Recommendation for Bumper Pull Horse Trailer
Updated 12/18/2025 | Published 08/07/2014
Question:
I have read all of your material and need to decide which jack to buy for my 2-horse bumper pull 4-Star trailer - I haul with Reese Equilizer bars to lift the weight off my truck as it is a bit under-powered. My tongue weight is only 1875#. There are so many to choose from it is difficult. I just need something to save my back during hookup. I am looking at either a Bulldog or the Atwood 80515.
asked by: Charmaine K
Expert Reply:
Since the Atwood Jack part # 80515 has been discontinued the decision would be pretty easy for you. The Bulldog Jack part # BD500200 is not only the obvious choice between the two you referenced, this jack is an excellent jack with plenty of power for your setup that has been reviewed highly by our customers who have bought and used it.
I attached an install and review video for this jack for you to check out as well.
Product Page this Question was Asked From
Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - White
- Camper Jacks
- Pop Up Camper
- Teardrop Camper
- Travel Trailer
- A-Frame Jacks
- Steel
- 3001 - 4000 lbs
- Electric Jack
- 22 Inch Lift
- Bolt-On
- 1 Jack
- Bulldog
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: tongue jack
- Shop: A-Frame Trailer Jack - Topwind - 5,000 lbs. by Dutton-Lainson
- Shop: Replacement Jack Foot for Dutton-Lainson 5,000-lb Trailer Jacks
- Shop: Square A-Frame Jack w/ Footplate - Drop Leg - Sidewind - 28-3/4" Lift - 3,000 lbs
- Video: A Closer Look at the Ultimate Trailer Jack
- Video: Ultimate Overview of the Replacement Jack Foot for Dutton-Lainson 5,000-lb Trailer Jacks
- Video: Looking at the Pro Series Detachable Footplate with Pin
- Q&A: Availability of 5,000 lb Top Wind Trailer Jack with Grease Zerk Fitting
- Q&A: Troubleshooting A Roll Pin That Won't Slip Into Place In A Bulldog 10K Square Jack
- Video: A-Frame Trailer Jack: The Breakdown
- Video: Hands-On with the Bulldog Square, A-Frame Jack
- Q&A: Are There Any American Made Trailer Tongue Jacks Available?
- Q&A: Replacement A-Frame Jack For Atwood Mobile Product Jack On Trailer With 2" Diameter Mounting Hole
- Q&A: Trailer Jacks Manufactured in the USA
- Shop: Ultimate Trailer Jack - A-Frame - Topwind - 27-1/2" Lift - 2,000 lbs
- Shop: Round A-Frame Trailer Jack - Sidewind - 15-5/8" Travel - 5,000 lbs
- Shop: Pro Series Detachable Footplate w/ Pin for 2" Diameter Jacks - 2,000 lbs to 5,000 lbs
- Shop: Trailer Valet JXC Trailer Jack w/ Footplate and Drill Powered Option - A-Frame - Sidewind - 1.2K
- Search Results: replacement awning
- Search Results: awning
- Video: Bulldog Powered-Drive Kit Review
- Shop: Trailer Wiring
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2016 Dodge Journey
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer wiring
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Brake Controller
on Camper Jacks
Steve K.
12/14/2025
I have a 2001 featherlight 3 horse bumper pull horse trailer. The trailer has an electric hitch Jack, I can’t find a brand name on the electric hitch. I need a manual hand turn rod for this electric trailer hitch.