bing tracking image
Q & A Icon

Troubleshooting Pullrite Capture Plate That Falls Off of Curt Flex Air  

Updated 11/13/2026 | Published 11/11/2026

Question:

Good morning. We have a Pullrite 21k slider hitch on our truck. We recently purchased a Curt Flex Air 21k pin box and capture plate for our trailer from Y’all. Unfortunately, the capture plate falls off when we unhitch. The capture plate yall supplied has one bolt on the back end of the plate that wedges against the King pin. No matter how tight we get it, it comes off when unhitching. Any help you can provide would be appreciated. Thank you

0

Expert Reply:

Hey Bruce, sorry to hear that the Capture Plate part # PUL98RR is giving you troubles. I did verify that this is the correct capture plate for the Curt Flex Air so you do have the right one.

Here are some things to check though:

Locking nut: Make sure the set screw has its locking nut installed and secured properly

Plate positioning: The capture plate should sit flush against the underside of the pin box's king pin plate.

Proper engagement: Check for excessive clearance, damaged hardware, or interference preventing the plate from seating correctly.

If that all checks out and its still not functioning properly let me know and also send me a picture of it installed if you can.

expert reply by:
0
Jameson C
Bruce P. profile picture

Bruce P.

11/12/2026

Jameson, the lock nut is positioned and tightened away from king pin. The plate is aligned and no gaps to the slide plate on the Pin Box. There does not appear to be any damage to any of the hardware. We are on our first long trip with the new Pin Box. We have had three stops and the capture plate has come off every time when unhooking. We are very careful to align the plate to the Pin Box, tighten the set screw as tight as I can do it with a ratchet and allen head socket. Then we tighten the lock nut with an open end wrench as tight as we can get it. For full disclosure, we have been traveling on the **Very ** rough I20 from Mississippi to Shreveport, then along mostly butter roads ( comparatively) to Central Texas. Dunno what the issue is, but we have had the same slider for over 12 years and have never had this issue with capture plates on 3 different Trailers. Same truck, same hitch. The Pin Box we took off of our current (Rhino pin box) Trailer had a capture plate that had set screws along the side of the plate/ slide plate on the Pin Box. So did the Capture Plate on our previous 5th wheel with a MoRyde pin box (front to rear). The wedge set screw alone doesn’t seem to work for us. Any ideas?

Jameson C. profile picture
Etrailer Expert

Jameson C.

11/12/2026

@BruceP Given that you've been using the same PullRite hitch for over 12 years without experiencing this problem, and considering everything you've described about how you're installing the capture plate, I don't believe this is simply a matter of not tightening the set screw enough. I did some additional research, and one thing I'd like to verify is the fitment of the capture plate itself. The PUL98RR is designed for Curt/Trailair Flex Air pin boxes, but PullRite specifies some fairly precise dimensions for the skid plate: Width: 13-1/4" Front of king pin to front edge of skid plate: 6-1/8" Rear of king pin to front edge of skid plate: 12-3/4" If your particular pin box differs from those measurements, it's possible the capture plate isn't engaging or retaining properly, even though it appears to fit correctly. Would you be able to verify those measurements for me? I'd also be interested in knowing whether the set screw and locknut are still tight when the capture plate comes off, or whether they've loosened. That would help distinguish between a retention/fitment issue and the hardware backing off.
Bruce P. profile picture

Bruce P.

11/13/2026

@JamesonC So, here are the measurements: Skid plate width: 13-1/4” *Front of King pin to front edge of skid plate: 6-1/8” *Rear of King pin to front of skid plate: +- 9” *Rear of skid plate to front edge: +- 12-3/8” * these are kinda hard to be exact on with the skid plate roundup in the front I’ll check the set bolt/locknut tightness later this morning and advise.
Bruce P. profile picture

Bruce P.

11/13/2026

@JamesonC So, the bolt and nut are very snug. Not sure if it backed out any because I didn’t mark it. But definitely cannot be turned by hand.

Product Page this Question was Asked From


Q & A Icon

Continue Researching

See More Q&A Expert Answers >>