bing tracking image
Q & A Icon

Will Gen Y Spartan Gooseneck Coupler Work With Recessed Ball 3" Lower Than Bed Floor In F450 ?  

Updated 09/28/2026 | Published 09/24/2026

Question:

Im interested in this ball hitch to offset the trailer back from the cab. I have an F450 with aluminum flatbed so the ball is recessed below the surface of the bed. I have a 12”x12” opening and the top of the ball sits 3” below the top of the bed. Will this hitch clear in that application? Thanks

0

Expert Reply:

Hey Quintin,

We may have a possible solution for you, but unfortunately none of the offset/shock-absorbing gooseneck couplers will work with your current ball sitting 3" below the top of the flatbed.

Gen-Y confirmed their Spartan coupler needs the ball to be within 1" of the top of the bed, and the Shocker 9" offset couplers allow a recessed ball only if the top of the ball is no more than 2" below the bed. Your 12" x 12" opening is large enough for the Shocker, but the 3" recess is still too deep.

What gooseneck hitch do you currently have installed in the F-450? If the ball is removable, we may be able to replace it with a 1" high-rise ball and get you within the clearance needed for the Shocker setup.

For example:

B&W Turnoverball: 1" High-Rise B&W Ball # BWGNXA2050 - adds 1" of height and fits B&W Turnoverball hitches.

Curt Double Lock/Flip and Store: 1" High-Rise Curt Ball # C60603 - also adds 1" of height.

If one of those fits your current hitch, raising the ball from 3" recessed to about 2" recessed would allow you to use the Shocker 9" Offset Shock-Absorbing Coupler # SHK26YR. It fits a 4" round gooseneck tube, is rated for 30,000 lbs, and gives you 9" of offset along with the air-cushioned ride.

The Gen-Y Spartan # GY96PR you were originally looking at would still require the ball to come up closer to the bed surface (within 1").

If your current gooseneck hitch does not have a compatible high-rise ball available, the last option would be replacing the truck-side gooseneck hitch with something like a B&W Turnoverball or Curt Double Lock so one of these high-rise balls can be used, or replacing it with a setup that places the ball closer to flush with the top of the flatbed.

If you can send me the brand/model of your current gooseneck hitch, or a picture of the ball and hitch assembly, I can see which route will work.

expert reply by:
0
Andrew N
Quintin M. profile picture

Quintin M.

9/27/2026

It is the factory Ford superduty gooseneck package that comes standard on their trucks.

Quintin M. profile picture

Quintin M.

9/27/2026

I should have added, the ball uses one detention ball on each side of it to look into a groove, there are no pins used.
Andrew N. profile picture
Etrailer Expert

Andrew N.

9/28/2026

@QuintinM Thanks Quintin, that helps clarify. It sounds like you have the factory Ford gooseneck prep package which is normally compatible with the Spartan or other offset couplers, but the aluminum flatbed is sitting higher than the original pickup bed floor. That’s why the top of your factory gooseneck ball ends up about 3" below the flatbed surface. Unfortunately, I’m not aware of a high-rise replacement ball for that Ford factory socket that would raise it enough for the Shocker coupler. With the ball still 3" recessed, you would be outside the clearance Shocker allows. At that point, you’d likely need to change the truck-side gooseneck setup so the ball sits closer to the top of the flatbed before using one of these offset couplers. Do you for sure need the offset? If not, you can use a standard straight coupler.

Product Page this Question was Asked From


Q & A Icon

Continue Researching

See More Q&A Expert Answers >>