Best Way to Improve Landing Gear Stability on a Grand Design Reflection 260RD
Updated 09/18/2026 | Published 09/11/2026 >
Products Featured in This Question
Question:
I have a Grand Design Reflection 150 Series 260RD that we take extended trips with. We are interested in improving its stability while camping and are trying to design between a rear-mounted option like the MORryde I-Beam Mounted Stabilizer for 5th Wheels and Travel Trailers Part Number: MR96RV versus a front mounted option like the MORryde X-Brace 5th Wheel Landing Gear Stabilizer Part Number: MR72AR . There is approximately 7 1/2 ft between the rear factory stabilizers and the end of the trailer. Do you have any recommendations between the two, or possibly another option? Thanks
asked by: Gary C
Expert Reply:
Hey Gary, thanks for reaching out. With 7-1/2 feet of trailer hanging behind the factory rear stabilizers, I recommend the MORryde I-Beam Stabilizer # MR96RV for your Reflection 260RD. That long rear overhang gives the back of the fifth wheel a lot of leverage to rock and bounce even with the factory stabilizers down. The # MR96RV lets you place the support farther back on the exposed I-beam, and its two legs plus ratchet strap help control both vertical movement and side-to-side motion.
The X-Brace # MR72AR is a great product too, but it mainly locks the front landing gear together to reduce lateral movement at the front of the fifth wheel. In your case, that 7-1/2' unsupported section behind the rear stabilizers stands out as the bigger weak point, so I recommend starting with the # MR96RV mounted as far toward the rear as the exposed I-beam allows. If you still want the coach even tighter after that, adding the X-Brace up front later makes a really nice combination.
Do you notice most of the movement in the rear living area when someone walks around, or does the entire fifth wheel feel like it is moving side-to-side?
Product Page this Question was Asked From
MORryde I-Beam Mounted Stabilizer for 5th Wheels and Travel Trailers
- Camper Jacks
- 5th Wheel Camper
- RV Motorhome
- Travel Trailer
- Stabilizer Jacks
- Manual Jack
- Bolt-On
- 1 Jack
- MORryde
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: What is Minimum and Max of MORryde I-Beam Stabilizer Height
- Q&A: Can MORryde I-Beam Stabilizer Install on Camper with Underbelly Cover
- Q&A: Do I Need One or Two of the MORryde I-Beam Mounted Stabilizer for a 35' Long 5th Wheel Trailer?
- Q&A: Will the Onan EC-AGS+ Auto Generator Start System Work w/the Onan QG 4000i DF generator?
- Q&A: Recommended SnapPad Jack Pads for a HWH Leveling System on a Motorhome
- Q&A: Which MORryde Stabilizer is Better? The Hitch or I-Beam Mounted Stabilizer?
- Q&A: How Do I Mount The MORryde I-Beam Mounted Stabilizer for 5th Wheels and Travel Trailers
- Article: Still Rocking After Leveling? How to Stabilize Your RV for Good
- Article: How to Measure for Travel Trailer and Fifth Wheel Steps
- Article: How to Level a Travel Trailer in 3 Steps
- Article: 30-Amp and 50-Amp RV Service: What's the Difference?
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Article: Spring Towing Readiness Checklist
- Article: How (and Where) to Connect an RV Propane Grill



Gary C.
9/17/2026
Thanks for the recommendation. That what I was thinking. My wife does notice the front bedroom does move around a bit if I'm in the back of the coach walking around or playing with the dog. I think we'll go with the rear stabilizers to start with. I notice that you have a couple of different brands of stabilizers. By and large, we're relatively happy with the MORyde products we have on the coach now, but I was also noticing that Beech Lane carries a stabilizer that attaches to the rear transverse I-beam along about 2/3 of its length. Would that provide better stability do you think? THanks