How Tight Should I Torque My Lug Nuts On Kenda Karrier KR35 ST175/80R13 With Aluminum AM03 Wheel?

Question

Question:

Hello! Thank you in advance. I recently purchased Kenda Karrier KR35 ST175/80R13 LRD Radial Trailer Tire w/ 13inch Aluminum AM03 Wheel - 5 on 4-1/2. What is the recommended torque?

asked by: Sean D

0

Expert Reply:

Hi Sean!

For the Kenda Karrier KR35 ST175/80R13 LRD Radial Trailer Tire w/ 13" Aluminum AM03 Wheel - 5 on 4-1/2 # KE34TJ you got, you will want to torque the lug nuts down to 75 to 85 foot pounds (80 would put you right in the middle of that and is typically where I go to when doing this).

If you are asking, I assume you already have a torque wrench. But if you don't, we do have those as well and the Powerbuilt Dual Drive Torque Wrench - 3/8" and 1/2" - 10 to 150 ft-lb # ALL944001 would have you covered.

What trailer are you installing these on?

expert reply by: Lazer S

0

Lug Nut Torque Specs
(click to enlarge)

Sean D.

7/16/2026

Hey Lazer! Thanks for the reply!! I wasnt sure if the steel sleeves changed the torque rating, so thank you very much for the direction. ???? These are being installed on a boat trailer. Can't wait to see them mounted ??!! Nothing like having your car wheels and trailer wheels look virtually the same! ?? Thanks again for your help! Sean

Lazer S.

7/16/2026

@SeanD You're very welcome! Glad I could help! ^___^ Having your car's wheels match the trailer's wheels will definitely be a good look as well! Especially with them being black. I always thought black wheels looked better than silver. Have fun out there and just let me know if there is anything else I can help with!

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 3

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 4

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

I apologize for any confusion on what the proper torque specs are for 1/2 inch lug nuts on trailer wheels. I attached a picture of a chart to the right that details what the proper torque specs are for a trailer wheels lugs based on lug size, wheel…

view full answer...

Answer 11

Hi Kyler! We definitely have center caps and lug nuts that you can use, but the Kenda Karrier KR35 ST175/80R13 LRD Radial Trailer Tire w/ 13" Aluminum AM03 Wheel - 5 on 4-1/2 #KE34TJ does not include them. With that said, I recommend the…

view full answer...

Answer 12

Hey Joshua, yes the Kenda Karrier KR35 ST175/80R13 LRD part #KE34TJ would fit in place of what you have now as it's exact same tire size and wheel bolt pattern. This will be a nice upgrade in capacity as well as will look a lot nicer as well. How…

view full answer...

How Tight Should I Torque My Lug Nuts On Kenda Karrier KR35 ST175/80R13 With Aluminum AM03 Wheel?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching