Will The Valterra RV Sewer Elbow T1035-1 Work With A Camco Brand Valve?
Updated 04/13/2026 | Published 04/05/2026
Question:
Will this work with a Camco valve too or do I need to buy a valterra valve?
asked by: Jay
Expert Reply:
Hey Jay, good question. You don’t need to stick with Valterra for this. The # T1035-1 will work with a Camco valve just fine as long as it’s a standard 3" connection. Yours should be a 3" connection but if you can check and verify that you can be sure it will work.
That 3" bayonet style fitting is pretty universal across RV waste systems, so the brands mix without any issues. As long as your valve is that standard size, it’ll hook up clean and seal like it should without the need for any additional adapters or anything.
How has your Camco valve been working out for you? Anything you wish worked smoother?
(click to enlarge)
Product Page this Question was Asked From
Valterra RV Sewer Elbow - 90-Degree - 3" Hub x 3" Rotating Flange
- RV Sewer Hose Fittings
- Sewer Elbows
- 90-Degree Elbows
- Hub
- Sewer Pipe to Waste Valve
- 3 Inch Diameter
- 3 Inch Diameter
- Rotating Flange
- Valterra
more information >
Continue Researching
- Shop: Valterra RV Sewer Elbow - 90-Degree - 3" Hub x 3" Rotating Flange
- Video: Hands-On with the Valterra ABS Solvent Cement
- Video: What to Know About the Valterra RV Sewer Elbow
- Shop: Valterra Bladex Waste Valve Body for RV Black Water Tank - Plastic Handle - 3" Diameter
- Shop: Valterra ABS Solvent Cement - 1/4 Pint
- Shop: Furrion Chill Cube Variable Speed RV AC System w/ ADB & Remote - 18K Btu - Non-Ducted - White - R32
- Q&A: Height and Width of Valterra RV Sewer Elbow # T1035-1
- Video: A Closer Look at the Valterra Elbow DWV Fitting for RV Sewer System
- Shop: Valterra RV Sewer Spigot with Flange - MPT - 3"
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Search Results: trailer hitch
- Q&A: Replacement for Atwood 61101 Brake Actuator
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Video: Furrion Chill Cube RV Air Conditioner Review and Installation - Travel Trailer Edition
- Shop: Trailer Wiring
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Article: Double-Eye Trailer Suspension System Review
- Q&A: How Does The Furrion Chill Cube Thermostat Get Wired To The AC System
- Search Results: trailer tires and wheels
- Video: Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vent Spec Review
- Search Results: trailer jack
- Shop: Suspension Enhancement
- Article: Trailer Brakes Not Working? Troubleshooting Guide
- Q&A: Recommended SnapPad Jack Pads for a HWH Leveling System on a Motorhome
- Q&A: Recommended Weight Distribution Hitch Rating for 2026 Grand Design Imagine 2670MK/2800BH
- Shop: Gooseneck Hitch
- Search Results: trailer hubs and drums
- Search Results: trailer leaf springs
- Q&A: Recommended Tow Dolly for a 8,800 lbs Travel Trailer
on RV Sewer Hose Fittings
Jay
4/9/2026
I actually bought the Camco a while back to install if my factory valves started leaking, but never installed it cause it hadn’t happened until recently.. So I saw the elbow and thought I’d much rather route the drain front to back and install the Camco vs adding it on the factory stuff as is and having it stick out past the side of the trailer..