Looking for Air Lift 60904

Question

Question:

Need to order Airlift 1000 60904 can’t seem to find it without browsing through every kit on 100 pages of kits. just point me in the right direction.

asked by: John C

0

Expert Reply:

Hey John, sorry for the confusion on that but the 60904 from Air Lift is our part number # AL95XV. We have the part numbers changed in our systems to organize them. Are you wanting a compressor kit as well?

expert reply by: Jameson C

0

John C.

4/1/2026

no compressor.

Jameson C.

4/1/2026

@JohnC Right on! You'd just need that kit then and you'd be set.

Answer 1

Hey Dennis! The Acadia and Traverse do share a lot, but the coil springs are different which means the #AL99PD will not fit your 2025 Traverse High Country. You may be able to use the universal springs like #AL60909 but you will need to measure to…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Looking for Air Lift 60904

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching