Lift Kit for 1994 Featherlite with Torsion Axle
Updated 02/19/2026 | Published 02/16/2026
Question:
I have a 94 featherlite 3 horse slant trailer. I need to put a lift kit on it and it has a torsion axle. I measured the holes center to center and theyre 10-1/2. What kit do i need to make the lifting kit brackets work? Thanks
asked by: Christopher L
Expert Reply:
Hi Christopher!
If you’re measuring 10-1/2" center-to-center on the mounting holes, the Dexter Torflex Lift Kit # K71-725-02 is very likely not going to bolt up to your brackets as-is. That kit is made specifically for Dexter #12 Torflex torsion axles, the bolt pattern on the lift kit is 9" center-to-center on the mounting holes.
The best next step is to confirm exactly which torsion axle you have, because lift kits are axle-specific. Featherlite has also used other torsion axle brands over the years (like AL-KO), so it’s not guaranteed that it’s a Dexter Torflex on your trailer. The only way to be sure is to check the axle tube for an ID tag or sticker. Dexter usually has a white label wrapped around the axle tube with a serial number and axle model.
If you can tell me what the axle tag says, or even snap a quick pic of the sticker, I can point you in the right direction.
Product Page this Question was Asked From
Torflex Lift Kit - Tandem Axle - 3-1/8" Lift
- Trailer Suspension Parts
- Alignment and Lift Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Tandem Axle
- Dexter
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: torsion axle lift kit
- Search Results: 4 on 4 trailer hub
- Search Results: jack
- Shop: B&W Continuum Weight Distribution System w/ Sway Control for 2" Hitch - 16K GTW, 1.6K TW
- Shop: Replacement Master Cylinder Cap with Diaphragm for Dexter Model 10 and 20 Brake Actuators
- Shop: Replacement Master Cylinder Filler Cap for Dexter Model 60 and Aero 7500 Actuators
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44643 Bearings - Pre-Greased
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-3/4 - Pre-Greased
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 5-1/2 - Pre-Greased
- Shop: Square Direct Weld Trailer Jack - Drop Leg w/ Spring - Sidewind - 12-3/8" Lift - 10,000 lbs
- Shop: Brake Controller
- Video: How to Choose a Trailer Brake Controller
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer wiring
- Shop: Suspension Enhancement
- Article: How to Measure for Trailer Hitch Drop
- Video: Redarc Tow-Pro Liberty Brake Controller Review RED24FR
- Q&A: Best Suspension Upgrade for 33" Tandem Axles: Road Armor vs Dexter EZ Flex for Ember 22ETS
- Search Results: trailer tires and wheels
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Search Results: trailer jack
- Video: What to Know About the Curt TriFlex NEXT Trailer Brake Controller
- Q&A: My Vehicle has a 4-Pin Trailer Plug, but Trailer has 7-Pin Trailer Plug
on Trailer Suspension Parts
