How Many 6-191 Jam Nuts Are Included?

Question

Question:

Dexter nut retainer part number 6–190. How many retainers do you get? Thank you

asked by: Scott S

0

Expert Reply:

Hey Scott. The Replacement Nut Retainer for 6-191 Jam Nut item # 6-190 is sold individually so you'll get a single retainer nut.

What kind of trailer do you have?

expert reply by: Jerred H

0

Jerred H.

10/22/2025

Hey Scott, did the single nut retainer work out for your setup? Your update could make it easier for others figuring out what they need for their trailer.

Answer 1

I have attached for you a set of photos which are used to identify the landing gear legs on a trailer. I assume you have either the older Lippert Ground Control 2.0 Leveling System or the newer Lippert Ground Control 3.0 Leveling System. If that is…

view full answer...

Answer 2

I have a solution for you and just as an FYI, Lippert had some difficulties with manufacturing and materials procurement during the pandemic; the Heavy Duty Driver Leg for Lippert Ground Control 2.0 Landing Gear #LC241846 was one of their parts that…

view full answer...

Answer 3

Hey Tom, the Replacement Heavy Duty Driver Leg part #LC241846 that you referenced is a lead screw type as it does not have any bearings.

view full answer...

Answer 4

We sure do Billy! That 241846 part number you gave me corresponds to the Replacement Heavy Duty Driver Leg for Lippert Ground Control 2.0 Landing Gear item #LC241846. The item #LC241846 is intended to replace the heavy duty master leg on Lippert…

view full answer...

Answer 5

I believe you are asking about the weld stops on the Replacement Heavy Duty Landing Gear Master Leg #LC241846. As shown in the attached diagram, the distance from the top of the upper weld stop to the bottom of the lower one on #LC241846 is 17.5…

view full answer...

Answer 6

There are a few things that go into making sure you choose the correct replacement landing gear. First you need to be sure that the landing gear is rated properly. If you check out the weight rating on your current landing gear just make sure the…

view full answer...

Answer 7

I spoke with my contact at Stromberg Carlson and the Replacement Lead Jack with Drop Leg, #LG-179013, is the same part as the Lippert Universal Fit Lead Landing Gear, #179013. The only difference between the two products is that they are sold through…

view full answer...

Answer 8

Hey Rodney, congrats on the new trailer! So long as you keep your tongue weights below 800 lbs the 8,000 lbs Fastway e2 Weight Distribution w/ 2-Point Sway Control item #FA94-00-0800 will still work on your new travel trailer. You'll be at the…

view full answer...

Answer 9

All of the Replacement Round Spring Bars for the Fastway e2 Weight Distribution systems, #FA94-02-1099, #FA94-02-0899, and #FA94-02-0699, measure 31-1/2 inches long. The diameter of the bar at the upper end is 1.39 inches, and the inside groove…

view full answer...

Answer 10

Hey Justin! The only thing you need to purchase to upgrade the 600 lbs TW Fastway e2 Weight Distribution item #FA94-00-0600 are the 1,000 lbs TW Replacement Round Spring Bar for Fastway e2 Weight Distribution Systems item #FA94-02-1099. What kind of…

view full answer...

Answer 11

Yes, the same head unit, part #FA92-02-1255, is used for your current 6K Fastway e2 Weight Distribution #FA92-00-0600 and the 8K version #FA92-00-0800. All you need to do is swap out your current trunnion bars with the Replacement Trunnion Bars…

view full answer...

Answer 12

The TPMS that came on your 2022 Rockwood Mini Lite 2204S allows you to manually set the minimum and maximum tire pressure limits similar to how the TST TPMS for RVs #TST-507-RV-4-C does. You will want to fill your tires to the 65psi that is indicated…

view full answer...

How Many 6-191 Jam Nuts Are Included?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching