Looking For Replacement Slide-In Arm For TorkLift Frame Mounted Camper Tie Downs

Question

Question:

Hello. I have kit F2022 on a 2018 F350 with a 2012 Lance 825. I run the fronts wider than the camper jacks. Anyway, lol. After 2 trucks with this camper I hit a planter in a parking lot and bent the Torklif slide in arm on the driver side. It was still sturdy enough to get me home but is bent about 30 degrees. Is it possible to buy just that part? Thank you, Jeremy Pike

asked by: Jeremy P

0

Expert Reply:

Hello Jeremy, thanks for reaching out. We do carry the TorkLift # TLF2022 tie downs but I am sorry to say we do not offer the slide-in arm portion by itself. It may be worth reaching out directly to TorkLift to see if they can provide just that part. Otherwise the only solution I can offer would be a whole new set of tie downs.

expert reply by: Jesse M

0

Jesse M.

9/2/2025

Hey Jeremy, did you have any luck reaching out to TorkLift about the slide-in arm? I'm curious to know if they were able to help, as it could be useful information for others in a similar situation.

Reply

Jeremy P.

9/3/2025

@JesseM I bought a piece of 1 1/2" square tubing, cut off the old end piece, welded it in place, drilled a couple new holes, spray painted it. Good as new. I swear I posted the original question on the Torklift website, not etrailer.

Reply

Jesse M.

9/4/2025

@JeremyP Oh nice! Hey don't knock it if it works, right? Glad to hear you got it sorted out though. Come back anytime you need anything!

Reply

Answer 1

I'm pretty sure that's to wire up a third brake light on a camper shell. To know for sure, take a circuit tester, like our part #PTW2993, and test that wire while applying the truck's brakes. If I'm correct it's a dedicated brake…

view full answer...

Answer 2

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 3

Hi Brandon! For the Dexter 5-Leaf Slipper Spring w/ Flat End for 10,000-lb Trailer Axles - 30-1/2" Long #DX45QR, you will want the Bronze Spring Eye Bushing, 3/4" x 1" x 2-1/2" #14-67. This is a direct replacement for what came in…

view full answer...

Answer 4

Hey Joe. I replied to your other commend but I'll go ahead and reply here just to make sure you see it. We do indeed have the MORryde GooseTech replacement for your MORryde rpb72-1621hd. For that you will need the following: - MORryde GooseTech…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Bruce, the Dexter 5-Leaf Slipper Spring w/ Flat End for 10,000-lb Trailer Axles #DX65QR is not the same as the Dexter 072-080-01, so yes the specs are correct. The spring you're referencing is the Dexter 5-Leaf Slipper Spring w/ Flat End for…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Looking For Replacement Slide-In Arm For TorkLift Frame Mounted Camper Tie Downs

Product Page this Question was Asked From

Continue Researching