Availability Of Repair Kit For Profile 2000 Winch On 1992 Lund Boat Trailer

Question

Question:

Hi, I just got a 92 Lund boat and trailer and the winch needs rebuilt. Do you have a kit for a winch that old, it’s a Profile 2000. I will try to send a picture as well. Thanks, Gerry

asked by: Gerry R

0

Expert Reply:

Hello Gerry, thanks for reaching out. We do have one repair kit for the Profile 2000 winches, the Winch Ratchet Repair Kit by Dutton-Lainson # DL70475. You can see what parts it comes with in the picture below.

If this does not contain what you need, it will be time to replace your winch. For that I recommend the following:

- Dutton-Lainson Hand Winch - TUFFPLATE Finish - Single Speed - 1,800 lbs # DL14627

expert reply by: Jesse M

0

Winch Ratchet Repair Kit by Dutton-Lainson
(click to enlarge)

Raley G.

3/6/2025

Do you have the small gear for it too

Jesse M.

3/6/2025

@RaleyG Sadly we do not. If your gears are busted, it would just mean a whole new winch.

Answer 1

Thanks for the picture! While we do not have an exact replacement for a Profile 2000 winch we do recommend the Dutton-Lainson Hand Winch item #DL14627 as a replacement. This winch has an 1,800 lbs capacity and will work great with the 20' x…

view full answer...

Answer 2

The only repair kit we have for your Profile 2000 hand winch is the Winch Ratchet Repair Kit by Dutton-Lainson item #DL70475. If this isn't what you are needing you will have to replace your winch. I recommend the Dutton-Lainson Hand Winch -…

view full answer...

Answer 3

Part #4769-28 is intended for several models of Fulton winch as listed on the item's page and we have not heard of anyone using it for a Dutton-Lainson winch. Since we do offer a complete D-L winch repair kit #DL70475 that is confirmed to work on…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Availability Of Repair Kit For Profile 2000 Winch On 1992 Lund Boat Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching