Is LaSalle Bristol Part # 34466N4AB96GMA Same as 66N4AB96GM

Question

Question:

Is this the same part as the Bristol Part 71-3444, 66N4AB96GM Thanks

asked by: Bert L

0

Expert Reply:

Hey Bert, yes the LaSalle Bristol Valve part # 34466N4AB96GMA that you referenced is exact same as their part number 66N4AB96GM.

expert reply by: Jameson C

0

Jameson C.

11/3/2025

Hey Bert, did the LaSalle Bristol valve end up being the exact match you needed for your setup? Knowing how it worked out could help others trying to confirm the same part.

Answer 1

It would be possible if you are willing to remove just the center section of the #34466N4AB96GMA and what you have now. The center portion would bolt right up to the flanges you have currently.

view full answer...

Answer 2

In my experience Valterra has been MUCH easier to get in contact with and get parts from than LaSalle Bristol. Dometic is the parent company for Valterra and typically has pretty good customer service every time I've called them. It's a bit…

view full answer...

Answer 3

In order to install a new Cable Actuator RV Waste Valve #34466N4AB96GMA, you're likely going to need to cut off the pipes at the spigot and hub in order to install the new waste valve. It's more than likely that ABS sealant was used to weld…

view full answer...

Answer 4

LaSalle Bristol doesn't make it so that you can replace much on their cable actuated waste valves besides just the handle so you would be better off just replacing the entire valve and cable system with Valterra's Black #TC372 and Gray…

view full answer...

Answer 5

Yes, the actual valve is the same for all of the LaSalle Bristol Cable-Actuated RV Waste Valves whether they have a spigot to spigot connection like part #34466N4BB96GM or spigot to hub connection part #34466N4AB96GMA. That said, you need to pay…

view full answer...

Answer 6

You should be able to tell which Valterra Double RV Waste Valves you need by inspecting your current connection points. The one end with the lugs on it is the same on all 3 parts so you simply need to determine if you need hubs, spigots, or a…

view full answer...

Answer 7

From what I can gather it sounds to me like you need the Valterra Eccentric Tank Reducer - RV Gray Water - 3" Spigot to 1-1/2" Hub #T1041-1. The 3" Spigot mounts directly in the gray water tank outlet while the 1-1/2" Hub slides…

view full answer...

Answer 8

The gate valve #34466N11AB96GMA should come apart without cutting the pipe once the bolts are removed. I can se that the flange is completely loose so the gasket must have gotten too hot and melted to both sides of the pipe fittings. You should be…

view full answer...

Answer 9

It can certainly be frustrating when the valves don't open and close correctly. Both Valterra and Bristol make excellent products, but even if the diameter sizes are the same, they aren't completely interchangeable. It is best to stick with…

view full answer...

Answer 10

If your gray water dump valve is a cable operated LaSalle Bristol #34466N11AB36GM, #34466N11AB48GMA, #34466N11AB60GM, #34466N11AB72GMA, #34466N11AB96GMA, or #34466N4AB96GMA, the correct replacement handle would be part #34490CMA1G, which is the only…

view full answer...

Answer 11

The cable is a fixed length and does not allow for tightening. It is recommended that you use a gentle u-shape, s-shape or gentle 90* bend in the cable and secure it every so often with cable ties part #DW05727-25 to take up the slack that you might…

view full answer...

Answer 12

Remove the locknut from the cable housing assembly of the #34466N11AB96GMA. Feed the cable through the mounting bracket or hold in the wall of chassis. Feed the locknut back over the cable and fasten securely to the backside of the bracket or wall.…

view full answer...

Is LaSalle Bristol Part # 34466N4AB96GMA Same as 66N4AB96GM

Product Page this Question was Asked From

Continue Researching