Replacement Converter for Progressive Dynamics PD9160a

Question

Question:

Recommended replacement for the PD 9160A

asked by: Jessica

0

Converter for RV
(click to enlarge)

Expert Reply:

Hey Jessica, the correct replacement for your now discontinued PD9160A would be the part # PD9260C which is also a 60 amp converter/charger.

expert reply by: Jameson C

0

Jameson C.

12/15/2025

Hey Jessica, how did the PD9260C work out as the replacement for your old converter? Knowing how it performed could help others looking to upgrade from the PD9160A.

Answer 1

I looked up the dimensions of your High Pointe EC942K9E and it's 15 inches deep, 15.7 inches tall, and 29.9 inches wide so the Furrion Over the Range RV Convection Microwave #FMCM15SS that you referenced would easily fit in place of it and would…

view full answer...

Answer 2

The only difference between the Progressive Dynamics Inteli-Power RV Converter and Battery Charger #PD9160A and the Progressive Dynamics Inteli-Power RV Converter and Smart Battery Charger #PD9260C is the charging cycles. The #PD9160A only has one…

view full answer...

Answer 3

Yes, the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 55 Amp, #PD4655V is what you are looking for. This upgrades or replaces the converter section for 55-amp Parallax/Magnetek, WFCO, or Parallax RV power centers and works…

view full answer...

Answer 4

Hi Jesus, The number you provided comes back as a Solera Edge awning in black, but we'll need a bit more information to determine the correct arm because there's 3 different models in black. There should be another sticker on the arm with a…

view full answer...

Answer 5

I do have an option for you but the Winnebago 147680-02-01A (Glo-Brite 122Y) is discontinued and no longer available. Therefore, you'll have no other option but to replace the light entirely but not to worry, this is actually very simple. I…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Replacement Converter for Progressive Dynamics PD9160a

Continue Researching