8" Tall Frame Brackets Needed For An Equal-i-zer Weight Distribution Hitch

Question

Question:

I acquired one of your trailer hitches from my son . My trailer frame is 8” frame . Do you make the brackets for 8” frame ? Thank you

asked by: Nick T

0

Expert Reply:

Hi Nick,

You just need the Outer Link Plate # EQ90-02-5378 and Inner Link Plate # EQ90-02-5208 to make your Equal-i-zer Weight Distribution System # EQ37140ET compatible with your 8" tall trailer frame.

expert reply by: Kevin C

0

Nick T.

9/20/2024

Thank you!

Answer 1

When choosing a weight distribution system, you want to go off the total tongue weight. This total tongue weight includes the loaded weight of the trailer tongue that you stated along with any cargo behind the rear axle of the towing vehicle. For the…

view full answer...

Answer 2

Hey Derek! Blue Ox 2-Point Weight Distribution w/ Sway Control #BLU75FR will fit your 8" tall I-beam frame on your trailer. I reached out to my contact at Blue ox just to double check and they said 8" is the max and it will work with an…

view full answer...

Answer 3

We do carry weight distribution systems with shorter spring bars, however, all of the spring bars for the Reese SC weight distribution systems are the same size. Unfortunately, they do not make shorter spring bars for this system. Instead, I…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 12

Hi Chas, The Lippert Road Armor Shock Absorbing Equalizer part #LC53CK may work for your trailer, but that will depend on what equalizer is currently on your trailer. In order to determine what equalizers would be a fit for your trailer, we'll…

view full answer...

8" Tall Frame Brackets Needed For An Equal-i-zer Weight Distribution Hitch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching