Is There a Wiring Harness For Tekonsha P3 Brake Controller on 2008 Chevy Silverado 2500

Question

Question:

Can you tell me what Tekonsha P3 wiring harness works with 2008 Chevy 2500 HD 4x4?

asked by: Rod P

0

Expert Reply:

Hi Rod,

There is not a plug-in wiring harness for a 2008 Chevy Silverado 2500 for the Tekonsha Prodigy P3 Trailer Brake Controller # 90195.

The wires are already run under the dash, and I have added a link below to a video which shows the install.

expert reply by: Kyle S

0

Rod

8/23/2024

Thanks Kyle!

Answer 1

The best Class V trailer hitch available for your 2007 Ram 3500 is the Draw-Tite #DT45509, This is the only option available for your truck that's designed to fit right under the bumper only when the factory hitch is removed, meaning it will sit…

view full answer...

Answer 2

I am not entirely sure what process you took so I'll give you some other things to try, or maybe a different way to test the Prodigy P3 #90195. First, sever the blue wire a couple inches from the back of your controller. Then use a circuit tester…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Is There a Wiring Harness For Tekonsha P3 Brake Controller on 2008 Chevy Silverado 2500

Featured Help Information

Miscellaneous Media

Continue Researching