Is There A 12-15' Long Hydraulic Brake Hose Available

Question

Question:

Go you have a product like Item KOD57FR but is shorter 12-15 feet in length? Thanks, Frank

asked by: Frank

0

Expert Reply:

Hey Frank,

The Kodiak Hydraulic Brake Hose - 3/16" Male Fittings w/ Stainless Flares - 1/8" ID - 15' # bh-3mfs-15 is the only hose we have with the same fitting sizes that falls within your 12-15 foot needed length. This hose is a bit more expensive because it comes with stainless steel fittings instead of brass ones like the # KOD57FR has, but stainless steel is better than brass so you are getting a better quality hose.

expert reply by: Kevin C

0

Answer 1

Is your trailer sitting as level as possible? Sounds like it could be sitting possibly nose high and combined maybe with a bit of play in the ball mount is creating the slamming you are experiencing. It's also possible your surge actuator has a…

view full answer...

Answer 2

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 3

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 4

How long of a line do you need? Do you know what size you need? The most common size is 3/16 inch like part #BH-3MFS-4-5 which is 54 inches long.

view full answer...

Answer 5

Yes it will, Belinda. As long as your total loaded trailer weight stays under 7,500 lbs, the DA75 Demco Disc Brake Actuator #DM33CV can absolutely support tandem axle disc brakes. Just make sure the brake lines and calipers are in good condition, and…

view full answer...

Answer 6

That's a really good question, and there is a difference between the 7,500 lb Dexter DX7.5L A-60 actuators for disc brakes; the differences are both in what they fit, as well as their length. - 14" Long & Top-Mounted For 3" Wide…

view full answer...

Answer 7

I did some research and found that the Kodiak Disc Brakes - 2 Wheel Set - 8" Rotor and Hub Spacer 3,500 lbs #K2HR35D-8 will be your best bet. This is compatible with your 5 on 4-1/2" pattern and your 10" wheels. The bearings and seals…

view full answer...

Answer 8

Hello Troy, thanks for reaching out. It may be possible to add brakes to your axle, as long as your axle is equipped with a brake flange. It will look like a square plate with four holes at the base of the spindle. If no brake flange is present, then…

view full answer...

Answer 9

My contact at Fulton confirmed that the A50 series is now obsolete and they don't make replacement parts. For a replacement, I recomemend the Titan Zinc-Plated Brake Actuator - Drum - Multi-Fit Ball - Bolt On - 7K #T43397007K with lockout…

view full answer...

Answer 10

I attached a chart that has the automotive cross reference for the Kodiak disc brake pads part #K2250CP that you referenced under the yellow heading. Probably the easiest to look up would be 1982 to 1992 Chevy Cavalier.

view full answer...

Answer 11

That is a tough question to answer as both are excellent manufacturers with their respective pros/cons. In regards to brake actuators, they both make and manufacture them here in the U.S.A. and they both come with a one year warranty. In regards to…

view full answer...

Is There A 12-15' Long Hydraulic Brake Hose Available

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching