Recommended Replacement Lippert Hydraulic Jack With 8 Mounting Holes

Question

Question:

I am looking to replace the middle jack on my drv 36rss3b 5th wheel ,this is aluminum and has 8 holes per side

asked by: Victor K

0

Expert Reply:

Hey Victor, it sounds like you're looking for the Replacement Hydraulic Jack Assembly for Lippert Level Up System # LC43ED which is black, measures 21 1/16" retracted, has 15" of travel, and also has 8 mounting holes.

expert reply by: Bryce D

0

Answer 1

Here is a list of all the Lippert Level Up replacement jacks we offer. Currently this is the only way Lippert offers their jacks and they do not offer a rebuild kit for these. Replacement Hydraulic Jack Assembly for Lippert Level Up RV Leveling…

view full answer...

Answer 2

Hello Mark, Per the tech at Lippert you are going to want to use AW-32 Hydraulic Fluid, and not an automatic transmission fluid.

view full answer...

Answer 3

Yes, as a matter of fact we have just what you need. The Replacement Hydraulic Jack Assembly for Lippert Level Up System #LC99ED is the Lippert 236560 part you mentioned. This jack has a maximum weight capacity of 14,00lbs, and measures 21-7/8"…

view full answer...

Answer 4

Hey Margaret! We do not have an installation video for the Lippert Polarity Reversing Solenoid by Trombetta for Hydraulic Power Units item #LC118246. I have attached a wiring diagram below that will show you how to get it set up though.

view full answer...

Answer 5

The Lippert Replacement Reverse Polarity Solenoid for RV Hydraulic Slide-Outs part #LC136046 and part #LC118246 are the same solenoid but vary in how they mount. The part #LC136046 mounts using a strap around the motor like what you have therefore…

view full answer...

Answer 6

Hey Darlene, thanks for the information! The ROHS 414849 is a Parker brand hydraulic pump motor that Lippert makes a replacement for. It's the Replacement Hydraulic Pump Motor item #LC167576. What kind of RV do you have?

view full answer...

Answer 7

The slide out could be malfunctioning for a number of reasons, but the motor or solenoid can very well be the culprit. Below I've attached a snippet from the manual that goes over how to test both the solenoid #LC118246 and the motor so that you…

view full answer...

Answer 8

Hello Vince, thanks for reaching out. The part number 414849 comes back as a Parker brand hydraulic pump motor. Lippert actually makes a direct replacement for this, and for that you will need the following: - Replacement Hydraulic Pump Motor for…

view full answer...

Answer 9

The MaxxAir Standard RV and Trailer Roof Vent Cover #MA00-933066 will fit your Ventline Ventadome Trailer Roof Vent #V2094SP-30. This will allow you to leave your vent open and run the fan even in the rain. You can also leave the vent open when you…

view full answer...

Answer 10

The Advent Air Replacement RV Air Conditioner part #ACDOM150 is the correct replacement for a Dometic setup. It will work in place of a ducted model and it will reuse the existing wall thermostat.

view full answer...

Answer 11

For a replacement for your Dometic B59516.711J0 AC we have the #ACDOM150 (white) or #ACDOM150B (black). These are directly compatible with your current Dometic setup so it will be a plug and play installation. The dimensions are 31-3/16" long x…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Recommended Replacement Lippert Hydraulic Jack With 8 Mounting Holes

Products Featured in This Question

Continue Researching