Do The TorkLift Camper Tie-Downs Include Installation Hardware?

Question

Question:

does all hardware come with frame brackets front and rear kits?

asked by: Mike

0

Expert Reply:

This can vary from vehicle to vehicle. On the TorkLift Camper Tie-Downs # TLC3205 you were looking at, these reuse the factory hardware on the truck. If you can tell me what other kit or kits you are looking at I can let you know if they come with hardware.

expert reply by: Bud M

0

Mike

3/27/2024

thank you for the reply that answered my question

Bud M.

3/28/2024

@Mike You're Welcome!

Answer 1

I have attached some photos showing what bolts the bottom brackets from the TorkLift Custom Frame-Mounted Camper Tie-Downs #TLC3205 will fit on compared to the photo you sent in. That upper tab with the 2 bolt holes will be on the rear-side of your…

view full answer...

Answer 2

Thanks for the photo it was really helpful and based on that, you do have the OEM hitch for your 2003 Chevy Silverado 2500HD. The hitch is unique in that it has the same open-end on the tubes, the same brackets, and same chain loops, which are all…

view full answer...

Answer 3

We do carry Torklift brand tie downs for your 2004 Chevy Silverado that attach to the truck frame but I would need more info from you to pick them out. What is your bed length? Do you have running boards? Factory hitch?

view full answer...

Answer 4

We do carry a camper tie-down system that will work for your 2004 Chevrolet Silverado without drilling into the truck frame. I recommend the TorkLift Custom Frame-Mounted Camper Tie-Downs, for your Silverado. This system includes the front and the…

view full answer...

Answer 5

Custom camper tie-downs that are mounted to the frame of your 2002 Chevrolet Silverado 2500 with 6-1/2 foot bed will be a lot more secure and stable than the clamp on, bed mount versions. They are custom built for your truck so they're…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

Hey Ross, the B and W Turnoverball #BWGNRK1067 wasn't designed to fit under a flat bed so there isn't an alternate set of measurements I can recommend. Are you sure it would clear under the flat bed? Normally we have to recommend the…

view full answer...

Answer 8

Yes. If you don't need the weight distribution bars attached to carry the trailer to storage, you can absolutely use just the WD hitch head and ball to tow the trailer. It will work just like a ball mount.

view full answer...

Answer 9

Hi Mark! For your 2020 Ford F250 with the 6-3/4 bed, running boards, and factory hitch, you are going to want the following two options: TorkLift Camper Tie-Downs - Custom Frame Mount - Front #TL77CR TorkLift Camper Tie-Downs - Custom Frame Mount -…

view full answer...

Answer 10

Yes, you can Jeff! You can still use your F-350's hitch to pull a trailer with the TorkLift Tie Downs item #TL87DR installed. You will most likely need an extension though to clear your in bed camper if you plan on towing a trailer with it in…

view full answer...

Answer 11

The Curt T-connector vehicle wiring harness for factory tow package 7 way and 4 pole flat connectors #C55774 is a confirmed replacement and fit for your Ford F-150 Lariat. It connects quickly and easily with no cutting or splicing of wires. The…

view full answer...

Answer 12

The towing capacity of the 2003 Chevrolet Avalanche 1500 with 5.3L V8 and 4.10 rear axle is 8100-lbs. For a 7600-lb GVWR travel trailer the resulting 500-lb safety margin is adequate/low-ish. With a trailer that weighs substantially more than the tow…

view full answer...

Do The TorkLift Camper Tie-Downs Include Installation Hardware?

Product Page this Question was Asked From

Continue Researching