What Bolt Is Used On The Replacement Topwind Knob Handle for Ram Jacks # TJPB-HD

Question

Question:

I am looking at Replacement Topwind Knob Handle for Ram Jacks Item # TJPB-HD. Can you tell me what the bolt size is on this? Thanks,

asked by: Caleb C

0

Expert Reply:

The bolt included with the Replacement Topwind Knob Handle for Ram Jacks # TJPB-HD is 6mm x 1.00 course threaded bolt. The length from the bottom of the head of the bolt to the tip is 1.25" with 7/8" of it not having threads.

expert reply by: Kevin C

0

TJPB-HD Bolt
(click to enlarge)

Answer 1

Hey Kelly yes, the handle diameter is the same for both #TJPB-HD and #TJD-7000-HD and the mount for both is the same size as well. The only difference between the two handles aside from the length are the jacks they fit. The Replacement Topwind Knob…

view full answer...

Answer 2

We have exactly what you are looking for! I reached out to my contact at Bulldog and the correct replacement handle for the Bulldog Square Swivel Jack w/ Round Pipe Mount - Drop Leg - Topwind - 28-1/2" Lift - 5,000 lbs #BD190708 you have is…

view full answer...

Answer 3

The Replacement Topwind Handle for Bulldog Topwind Jacks #BD105212701 has a 3/4" shaft diameter, so it might be what you're looking for.

view full answer...

Answer 4

Yes, we do carry the correct replacement handle for the Square Direct Weld 7K Jack part #TJD-8000. It's the Replacement Topwind Handle part #TJD-7000-HD which is exactly what the jack would have come with when new and it's an easy bolt-on…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

What Bolt Is Used On The Replacement Topwind Knob Handle for Ram Jacks # TJPB-HD

Product Page this Question was Asked From

Continue Researching