Do I Have to Drill to Install the K-Source Extendable Towing Mirrors on a 2015 Chevy Silverado 1500?

Question

Question:

Will I have to drill a fourth hole on a 2018 Silverado 1500?

asked by: Mike

0

Expert Reply:

Yes, you will. The longer length of the K-Source Custom Extendable Towing Mirrors item # KS62147-48G over the factory mirrors requires you to drill an extra hole for an additional support. These mirrors are confirmed to fit your 2018 Chevy Silverado 1500.

I have linked an installation video below that we did on a 2015 Silverado along with a diagram outlining the drilling steps. If you skip ahead to the 3:50 mark you'll see the process of getting this hole drilled. The installation will be the same on your 2018 Silverado.

expert reply by: Jerred H

0

Drilling Steps
(click to enlarge)

Answer 1

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 2

Hello David, thanks for getting in touch. The 2019 GMC 1500 AT4 has a 2" lift, and the #AL88388 kit you mentioned has taller brackets to fit the 2" lift. I looked up the X31 model and it does say it has offroad suspension, but it didn't…

view full answer...

Answer 3

The K-Source Snap & Zap Custom Towing Mirrors #KS80930 I feel are the best mirrors extensions for your 2024 GMC Sierra 1500. These have all the cut outs for turn signals, puddle lights and cameras you may have on your mirrors. The snap on design…

view full answer...

Answer 4

For your 2019 Jayco Jay Flight SLX Travel Trailer that's being pulled by your Ford F-150 I highly recommend the Equal-i-zer Weight Distribution System #EQ37100ET. This is a fantastic system that uses integrated 4-point sway control to greatly…

view full answer...

Answer 5

Hey Eric, thanks for reaching out! Ultimately, I'll need more specific info on your trailer (the GVWR would be best), but I can still help you figure out how to choose a weight distribution hitch (WDH). What you'll need to look for is the max…

view full answer...

Answer 6

Yes, the Reese Titan Reducer Sleeve 2-1/2" to 2" #58102 is a great option to pair with your B&W Tow & Stow 2-Ball Mount #BWTS10037B.

view full answer...

Answer 7

Hello again Joe; the etrailer RV Cover for Travel Trailers #e97VV does have zippers to allow access with the cover on which can be seen in the video attached below. This will work as long as you measured correctly. You need to measure the body of the…

view full answer...

Answer 8

Hello Allan, thanks for reaching out. The K-Source Snap & Zap Custom Towing Mirrors #KS48NQ will not obstruct the 360 degree camera on your 2022 Toyota Tundra. The towing mirror does not actually cover the part of the mirror that has the camera.…

view full answer...

Answer 9

The Angled Hold-Downs for Truck Bed Campers #HSAB that you referenced are universal in design so they can fit nearly all truck beds including your 2015 GMC 3500 with a long bed. They don't fit some dually beds. The fit issue with the dually…

view full answer...

Answer 10

For a spare tire and wheel on your 2023 Coleman Lantern 17B use the Karrier ST215/75R14 Radial Trailer Tire - 5 on 4-1/2 - Load Range C - Galvanized Wheel #AM32182 or White Wheel #AM32181.

view full answer...

Answer 11

The Adco Olefin HD All-Climate + Wind RV Cover for Travel Trailer #AD27ZR has three zippered panels on the passenger side so that you can access your entry doors no matter where they are on your trailer. If you look at the 4:05 minute mark of the…

view full answer...

Do I Have to Drill to Install the K-Source Extendable Towing Mirrors on a 2015 Chevy Silverado 1500?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching