How Long Will The Air Lift LoadLifter 5000 Air Helper Springs # AL57231 Take To Install?

Question

Question:

What’s the installation time

asked by: Adam

0

Expert Reply:

For an average DIY installer the Air Lift LoadLifter 5000 Air Helper Springs # AL57231 should take 2-3 hours to install. If you are also looking to install the Air Lift WirelessAIR Compressor System # AL74000EZ at the same time this will add another hour to the time above.

expert reply by: Bud M

0

Answer 1

I have an air bag solution for you. Unfortunately, if you have a 2022 Ram 3500 CA60 chassis cab, the Air Lift LoadLifter 7500 XL #AL57531 will not fit. This is because these air bags are only designed for standard pickup models. However, we do have…

view full answer...

Answer 2

You are going to want a heavy duty air spring system for your 2020 Ram 3500 crew cab. I recommend the Air Lift LoadLifter 7500 XL Air Helper Springs item #AL57531 you were looking at. This is our highest rated system and fits both the 2WD and 4WD…

view full answer...

Answer 3

Hey Kenny, welcome back! Yes, you can install the Air Lift Air Helper Spring Cradle #AL59DQ on your 2016 Sierra 3500. This works for lifted applications as well as trucks at stock height. Since it replaces the lower mounting point and the air bag…

view full answer...

Answer 4

I have included a picture that shows the measurements needed for a spindle, bearings, seals, faces, and hubs. The spindle measurements are labeled A through F. A is the spindle shaft diameter B is where the grease seal sits C is where the inner…

view full answer...

Answer 5

According to the folks at AirLift, their air helper spring systems are compatible with Daystar Cradles, but using them will void the product warranty of the air helper springs. Some folks at Firestone have told us the same about their Ride-Rite…

view full answer...

Answer 6

Hey John, yes the flow through sensors like the part #TST-507-FT-S4 and the cap style like part #TST-507-RV-S2 both work with the 507 style monitor you have now. The flow through is generally the preferred style since it allows you to inflate through…

view full answer...

Answer 7

We do have 6-Pole Square Trailer Wiring Connector Kit (Car and Trailer Ends) #37995 that you can use for your Arctic Fox camper. This is both the male and female ends. But the wires on them are 18 gauge. You could replace the ground and power wires…

view full answer...

Answer 8

Hey Steve, The AirLift airbags with internal jounce bumpers are not able to be added to a system without so you would need to get a whole new system. With that said the system with the internal jounce bumpers is going to create a much rougher ride…

view full answer...

Answer 9

Hey Greg, we have the Air Lift LoadLifter 5000 #AL57231 that fits your 2019 Ram 3500 4WD but the part number you mentioned does only fit the 2WD models. Are you wanting a compressor kit too?

view full answer...

Answer 10

Hello Mike, Sounds like you are getting things set up the right way and not going over your payload, I respect that. It looks like the weights are the same whether you have a 6 3/4' or 8' bed. If you happen to have an aftermarket hitch,…

view full answer...

Answer 11

To determine the size of spacer that you will need to install #F2304, you will need to measure the space between the bottom of the frame to the top of the axle. If this measurement is 6-1/2 to 7-1/2 inches you would need a 1.25 inch spacer set…

view full answer...

How Long Will The Air Lift LoadLifter 5000 Air Helper Springs # AL57231 Take To Install?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching