Replacement Arms For Yakima EXO SwingBase # Y34VR

Question

Question:

Do you have the replacement right arm for the Exo Swingbase?

asked by: Ken

0

Expert Reply:

Yes, we also have the Replacement Right Arm # Y76KV for the Yakima EXO SwingBase # Y34VR. This is the other side from the Left Arm # Y66KV you found.

expert reply by: Bud M

0

Answer 1

I got some information from Yakima and included a diagram of the EXO SwingBase #Y34VR, which is the base part for the EXO SwingBase 2 Tier #Y82VR. Though the measurement from the pin hole to the closest edge of the carrier is not included in said…

view full answer...

Answer 2

Hey Gabriel, You would need a factory wire harness from Dodge first and could then install the Pollak 5th Wheel / Gooseneck T-Connector with 7-Pole #PK11893-33-32 inline with the factory harness to get a 7-way socket in the bed of the truck as well.…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Hello James, I am at a loss why Draw-Tite #75882 classified theirs as a class 4, it can handle the same weight as the Curt #C13207. The most concealed hitch would be the Curt #C13295, but it has the lowest towing weight so I am crossing that one off…

view full answer...

Answer 8

Hey Justin, so I checked with B and W and they only have fits that run up to 2024 BUT since we know they 2024 and 2025 trucks are unchanged in terms of gooseneck hitches we know the Turnoverball part #BWGNRK1020 is a fit and will work great.

view full answer...

Answer 9

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 10

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

Yes, we do. What you are describing sounds like the Inner Frame Brackets for Under-Bed Rail and Installation Kit for Reese Elite Series 5th Wheel Hitch item #RP27FR. I have attached a picture below. These come welded to the frame exactly where you…

view full answer...

Replacement Arms For Yakima EXO SwingBase # Y34VR

Product Page this Question was Asked From

Continue Researching