Does Trimax Trailer Coupler Lock Work on A-Frame Coupler

Question

Question:

Will this lock work on an A-frame coupler?

asked by: Robert

0

Expert Reply:

Yes, the Trimax Universal Trailer Coupler Lock for 1-7/8", 2", and 2-5/16" Couplers # TMX47FR does indeed work on an A-Frame coupler.

expert reply by: Kyle S

0

Answer 1

I sure do! I recommend spraying all the moving parts and the areas around them on your Bulldog Collar-Lok Coupler item #BD028386 with WD-40. Use an excessive amount and completely saturate your coupler and let it sit. Make sure you spray it inside…

view full answer...

Answer 2

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 5

Hi Hilario, congrats on the new truck! ^___^ If this were my truck and I was installing a retractable cover on it (which I actually did with my Silverado), I would go with the manual RetraxPRO XR Hard Tonneau Cover - Retractable - Aluminum - Matte…

view full answer...

Answer 6

The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include…

view full answer...

Answer 7

Hey Brian! Yep, for your boat trailer, I’d skip the etrailer A-frame drill jack #e38AV since your trailer doesn't have that standard 3-bolt A-frame jack mount. That could be fabricated to fit, but that's a lot of unnecessary work. For a…

view full answer...

Answer 8

Hey, Carl. There isn't one specific lock that would be for that coupler. I tried to find some sort of picture of even a drawing of the coupler to see what style would be best for it but I couldn't find anything out there. What I do know about…

view full answer...

Answer 9

It sure will Dakota! The Pacbrake Alpha HD Air Bag Suspension Kit item #PB75ZV has been confirmed to fit the 2018 Ram 1500. It works with the 2WD and 4WD models. They have a 5,000 lbs capacity. The Pacbrake item #PB75ZV are not designed to increase…

view full answer...

Answer 10

Hi Alex! The Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers - 2" Hitch - 5" Drop/Rise - 16K #325-GH-513 is just the regular ball mount, but you can grab the Pintle Lock for Gen-Y Adjustable Ball Mounts w/ 2" Receivers #325-GH-032…

view full answer...

Answer 11

Not all aluminum trailer frames are strong enough for use with a steel weight distribution (WD) system. It is possible that the stronger steel WD components could put too much stress on the frame. If your trailer has an aluminum frame you'll…

view full answer...

Answer 12

No long-term contract, Natalie - but a service plan is required to use the trackers. When you buy the 3000 with wifi assist #PM84FR, 5000 #PM64FR, or 5000 with wifi assist #PM74FR from etrailer, you’re purchasing the hardware/device only. To activate…

view full answer...

Does Trimax Trailer Coupler Lock Work on A-Frame Coupler

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching