How to Wire the Deka Battery Isolator item # DW08771

Question

Question:

How to wire the deka 08771 to a 2010 Chevy Silverado 1500, for second battery in truck camper.

asked by: Greg

0

Expert Reply:

I went on Deka's website and found a wiring diagram I have attached below. To install the Deka Battery Isolator item # DW08771 you will want to follow these steps:

Terminal 1 would connect to the positive battery terminal of the main battery.

The original wire from the alternator to the main battery would be removed from the battery and installed on terminal 1.

Terminal E would connect to an ignition circuit that's hot only when the key is switched on via a 6 amp breaker.

Terminal A would connect to the battery lead on the alternator.

Terminal 2 would connect to the positive terminal of the auxiliary battery.

expert reply by: Jerred H

0

Deka Battery Isolator
(click to enlarge)

Answer 1

The best replacement we have for your Innoflame RV48D80L-1 fireplace is the Furrion Electric RV Fireplace with Crystals #FF40SW15ABL. This fireplace is a bit smaller, measuring 39-7/16" wide x 17-3/4" tall x 6-1/4" deep, has 4…

view full answer...

Answer 2

Hi Hugh, When it comes to RV fireplaces most manufacturers won't supply replacement parts so on our end it's always led to a complete replacement of the unit. You can try reaching out to Innoflame and seeing if they'll give you parts…

view full answer...

Answer 3

For The Deka isolator #DW08771, Terminal A will connect to the alternators battery lead. Terminal E will go to the hot ignition circuit via a 6 amp circuit breaker. I have included a wiring diagram below for your reference.

view full answer...

Answer 4

When installing the Deka Battery Isolator - 120 Amp #DW08771 you actually do not tap into the ignition systems. Instead you will run the wire from the alternator to the A post on the Isolator, then run a wire from the number 1 post of the isolator to…

view full answer...

Answer 5

What you are describing sounds like how the DEKA isolator part #DW08770 is designed to be wired. If you check out the attached diagram you can see what I mean.

view full answer...

Answer 6

The Deka Battery Isolator - 95 Amp #DW08770 does require the ignition switch be connected to the E post. This is how you ensure the batteries are isolated and the auxiliary battery does not draw power from the starting battery. You will want to use a…

view full answer...

Answer 7

I attached a diagram that shows how the Deka Battery Isolator #DW08770 wires to a vehicle/battery.

view full answer...

Answer 8

You would not need a new plug. You would run the positive wire from the alternator to the 1 and A post of the Isolator #DW08771. Check out the attached picture for a wiring diagram.

view full answer...

Answer 9

It sounds like you're trying to replace the battery isolator solenoid. This is what allows the starting battery on your 2018 Jayco Precept Prestige to charge the house batteries when the engine is running, but keeps the house batteries from…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

How to Wire the Deka Battery Isolator item # DW08771

Product Page this Question was Asked From

Continue Researching