Are Two Different BaseClip's Needed for a Yakima Roof Rack on a 2023 Maxda CX-5 with Naked Roof

Question

Question:

Scott suggested these for my naked Mazda CX5 for a Hullivator install. I just want to be certain I need two different SKUs...please confirm! Thank you. Suggested: Y06130 and Y06154

asked by: Tara

0

Expert Reply:

Yes, the two different BaseClip's are correct for your 2023 Mazda CX-5 with naked roof. The BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers # Y06130 is for the front bar and the BaseClip Fit Kit for Yakima BaseLine Roof Rack Towers # Y06154 are for the rear bar.

The rest of the roof rack kit is the:

- Yakima HD Crossbars # Y01156
- BaseLine Towers for Yakima Crossbars # Y28TR
- HD Bar SL Adapter for Yakima BaseLine # Y03541

This will allow you to use the Thule Hullavator Pro Kayak Roof Rack and Lift Assist # TH898.

expert reply by: Scott S

0

Answer 1

Yes, the older Thule Hullavator (897XT) will fit Yakima JetStream bars. You'll use the T-Slot mounting hardware that would have come with the older model carrier and then you need to make sure you can move the carrier out far enough that there is…

view full answer...

Answer 2

Congratulations on your new vehicle! For the naked roof on your 2018 Mazda CX-5, I highly recommend the Thule WingBar Evo Roof Rack. This system consists of #TH711420 for the two 53 inch aluminum WingBar Load Bars, #TH710501 for the Evo Clamp Feet,…

view full answer...

Answer 3

Yes, there is a roof rack that will fit your 2023 Mazda CX-5. This mounts directly to the side of your roof without drilling and has more than enough capacity for a bike rack. You will want the roof rack by Rhino Rack and it includes the following…

view full answer...

Answer 4

The current Thule Hullavator part #TH898 requires bar space of approximately 28.5 inches so you'd need a rack with around 60 inch crossbars like the Malone Roof Rack part #MPG203 which is a confirmed fit for the raised rails of your 2015 Subaru…

view full answer...

Answer 5

The Thule Traverse Roof-Rack Foot Pack 754/480 has been discontinued for a bit now so they are not going to be available for your new 2021 Mazda CX-5. In addition to that, since Thule changed the way the SquareBar attaches to the new feet you'd…

view full answer...

Answer 6

Yes the Inno Square Crossbars part #INB137 are the same 7/8" tall and 1 1/4" wide as what the original Thule Square bars were. They will work with the older Thule Foot Packs for square bars like part #TH450. As you know they are a pass…

view full answer...

Answer 7

I'm not quite sure what you're asking, but let me see if I can clear some things up for you. The Thule Hullavator Pro Kayak Roof Rack and Lift Assist w/ Tie-Downs #TH898 is compatible with both the Inno Crossbars #INB137 you were looking at…

view full answer...

Answer 8

I have a solution for you, but the Rhino Rack Pioneer Platform #RR25TB is designed to mount directly to either a Rhino Rack fit kit or Rhino Rack HD bars so you'll need a Pioneer platform that mounts to crossbars. There are 2 different sizes of…

view full answer...

Answer 9

The older style of Thule square bars are no longer made but I do have a solution for you. The Inno square crossbars are the exact same dimensions and will fit your Thule feet so you'd want the #INB137 for a set that is 54 inches long. The new…

view full answer...

Answer 10

For your 2019 Mazda CX-5 with a bare roof, you will also need a fit kit to mount the Inno Feet for Square Crossbars #INSUT. Fit kits are designed to conform to specific vehicles and give the feet a mounting point, which is why they are needed, and…

view full answer...

Answer 11

Yes, you can reuse your Thule SquareBar item #TH712300 with your 2023 Mazda CX-5 but they will be 3" shorter than the item #TH712400 that is recommended to be used. Since you'll be reusing the same bars the Thule Hull-a-port carriers will…

view full answer...

Answer 12

I went out into our showroom and measured the dimensions of a set of discontinued Thule square load bars and found that they are 7/8 of an inch by 1-1/4 inches. This is identical to the Inno square bars like #INB137.

view full answer...

Are Two Different BaseClip's Needed for a Yakima Roof Rack on a 2023 Maxda CX-5 with Naked Roof

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching