1/4" Diameter Locking Pins Which Can Be Keyed Alike

Question

Question:

I am looking for 3- 1/4” pin locks that are keyed the same

asked by: Randy N

0

Expert Reply:

Here is a list of different length 1/4" pin locks we offer which can be keyed alike.

1/2" Long Pin Lock # e98885
7/8" Long Pin Lock # e98890
2" Long Pin Lock # e98886
2-1/2" Long Pin Lock # e98887
3-3/8" Long Pin Lock # e98888

We also have the Adjustable 1/4" Lock # e98883 which can fit from 1/2" to 2-1/2" spans you can get keyed alike as well.

expert reply by: Bud M

0

Answer 1

We have the perfect replacement for your Global Direct GDC-80 brake actuator. Since you mentioned "down tongue" I believe you were referring to having an actuator with drop. If you have disc brakes, the best option is the Demco Hydraulic…

view full answer...

Answer 2

You absolutely can! To lock the coupler latch of the Demco Hydraulic Brake Actuator #DM8104311 you were looking at to the hitch ball on your vehicle you will need to use the coupler lock #e98887 which gets inserted into the hole on the latch shown in…

view full answer...

Answer 3

Since the Titan Zinc-Plated Brake Actuator #T4750820 that you referenced has a weight capacity of 12,500 lbs and a tongue weight capacity of 1,250 lbs it will serve well as a replacement actuator for your application. The mounting holes are spaced…

view full answer...

Answer 4

You could run a bolt through the #DM8104311 to manually lock it out if the solenoid fails. However, there is no spot on the actuator to do this so it would require drilling. A Replacement solenoid #DM11993 is also available. The hole would require a…

view full answer...

Answer 5

I reached out to Demco for you on the Demco Hydraulic Brake Actuator with Drop and Electric Lockout part #DM8104311, they informed me that the distance from the center of the rear mounting hole to the end of the casing is 7-3/4". I have attached…

view full answer...

Answer 6

In order to recommend a replacement master cylinder, I'd need to know the manufacturer and model number of the existing brake actuator. We carry replacement master cylinders for certain Titan, Dico, Atwood and Demco brake actuators. If parts are…

view full answer...

Answer 7

Yes, we have the Demco Composite eZ-Latch Repair Kit #DM6288 that will replace the eZ-latch on Demco 2-5/16" cast couplers like that which comes on the Demco Hydraulic Brake Actuator #DM8104311.

view full answer...

Answer 8

The Titan Actuator part #T4750820 would be a great solution for replacing the GDC 120 you have on your triple axle boat trailer. It has more than enough capacity and is a very reliable actuator.

view full answer...

Answer 9

You can use Master Lock #ML389DAT for coupler #CTA-280. Another option is to use a latch lock so that the latch cannot be opened. Most latches, if they can accept a lock, will take a 1/4 diameter pin such as #e98888 or #3008.

view full answer...

Answer 10

The Blue Ox Adjustable Trailer Coupler Lock #BLU56XR comes as individual lock numbers so for a keyed alike option I recommend checking out the etrailer Surge Brake Coupler Lock #e98888 which has the same specs but is only 1/8" shorter. The…

view full answer...

Answer 11

We do have locks that will work with your Dexter A-60 Brake Actuator #DX56FR. The Coupler Lock #e98888 will allow you to secure the trailer to your vehicle when towing. This lock pin replaces the included push pin which comes with the actuator. For…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

1/4" Diameter Locking Pins Which Can Be Keyed Alike

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching