What Monitors Work with the Rear View Safety Flush Mount for 7" Monitor

Question

Question:

Will this fit my Haloview Byte Tango 7, 7inch monitor?

asked by: Bill B

0

Expert Reply:

The Rear View Safety Flush Mount for 7" Monitor part # RVS-421 is designed for the Rear View Safety Backup Monitor part RVS-6137N which measures 7" long x 5-1/4" tall x 1" deep. Unfortunately, we cannot confirm fit of the mount on any other monitor but if your dimensions are the same or similar you may be able to make this work for you.

expert reply by: Conner L

0

Answer 1

Hey Jeff, thanks for reaching out. Aside from the suction cup mount, there is one other mount for 7" WiSight display. Take a look at the Voyager Universal Mount #VOSHD6MNT. This allows for permanent installation on your dash and uses a ball and…

view full answer...

Answer 2

In order to replace the Voyager Monitor VOM-783CT you will need both the Voyager RV LCD Observation Monitor part #VO34FR and CRT to LCD Monitor Cable Adapter part #31100041.

view full answer...

Answer 3

The #VO344FR monitor you mentioned wouldn't be compatible, the correct replacement would be part #VOM719WP. I've linked you to a product description video. I hope that helps!

view full answer...

Answer 4

No, there is not and there is not a work around available that allows you to control the camera's tilt feature without the original monitor. We get this question often and I am sorry but upgrading your monitor will cost you that function. To…

view full answer...

Answer 5

The cut out dimensions needed to install the RearView Safety Flush Mount Bracket #RVS-421 are 7-1/4 inches wide by 5 inches tall.

view full answer...

Answer 6

I wasn't able to find much information on the exact replacement for your Ventline AS-13 M-VA 203 roof vent. The only information I found said it had an overall width of 8-1/2" and uses a 6" fan. It sounds like you will need the…

view full answer...

Answer 7

You will not need to use the splice kit, but you will need to use new wiring in order to upgrade to and install the Rear View Camera system you asked about: - Rear View Safety Backup Camera System #RVS-770613-NM This camera system comes with its own…

view full answer...

Answer 8

Hello Chris, Yes, the correct replacement monitor for the RVS-6137-NM is the Rear View Safety Backup Monitor - 7" Color Screen #RVS-6137N. If you don't mind me asking, how long did the original last before going to it's final resting…

view full answer...

Answer 9

Hey Ted, thanks for the information! To replace your Ventline as-13 m-va 204 cover, you'll want the Replacement Plastic Dome Assembly for Ventline Vanair Trailer Roof Vent item #BVA0502-03. This cover measures 8-1/2" wide with the 2 screw…

view full answer...

Answer 10

An AS-13M is an older Ventline model so I recommend just replacing it with a MaxxFan Mini Plus Manual RV Roof Vent #MA00-03851. This powered vent features a rain shield that will allow you to use your vent in any weather or even while driving. The…

view full answer...

Answer 11

I believe I have exactly what you need to add the desired backup camera(s) to your Ford F-150. For starters, you will need a monitor and for that I recommend the Rear View Safety Backup Monitor part #RVS-6139N. The monitor does come with a universal…

view full answer...

Answer 12

The switch would not effect the speed of the fan. It sounds like your motor is either getting inconsistent power or the motor itself is failing. You can test the current using a multimeter like #PT89ZR. A bad ground may be at fault or you may need to…

view full answer...

What Monitors Work with the Rear View Safety Flush Mount for 7" Monitor

Product Page this Question was Asked From

Continue Researching