Can the EZ-Jack be Used on a Triple Axle Trailer

Question

Question:

Hi, How do you recommend jacking up a triple axle trailer? Is there a EZ-Jack type system for this?

asked by: Howard G

0

Expert Reply:

I spoke with my contact at EZ-Jack and he says that to use the EZ-Jack on a triple axle trailer you will need to turn the curve up, opposite the wheel, and drive up on the jack and you will be able to change the tires.

Other wise a floor jack and jack stands are the safest way to service trailer axles.

expert reply by: Robert G

0

Answer 1

Hey Joshua, yes the Kenda Karrier KR35 ST175/80R13 LRD part #KE34TJ would fit in place of what you have now as it's exact same tire size and wheel bolt pattern. This will be a nice upgrade in capacity as well as will look a lot nicer as well. How…

view full answer...

Answer 2

Hey Darryl, thanks for reaching out. Yeah, you definitely got a little carried away on the grease, and you’re not the first one to do it after watching a few videos. 14 oz is way too much, and what happens is exactly what you saw, it pushes past the…

view full answer...

Answer 3

The Blaylock EZ Jack and Wheel Chock for Tandem-Axle Trailers #EZ-JACK can fit trailers with leaf springs. If you check out the picture I attached you can see it used on a leaf spring trailer just like yours.

view full answer...

Answer 4

The Andersen Rapid Jack part #AM3620 and Blaylock EZ Jack and Wheel Chock part #EZ-JACK are both excellent options to help quickly and effectively change a trailer tire. I spoke with each of the respective manufacturers but neither we able to give…

view full answer...

Answer 5

It sure does Steve! Our 3,500 lbs etrailer Electric Trailer Jack w/ Tongue Weight Scale item #e43KV also comes in a 5,000 lbs capacity. We have two different options depending on how you want to power it that I have listed below: Wired to Trailer -…

view full answer...

Answer 6

Hi Darrell! The Americana Trailer Wheel Lug Nut #AM90049 is a single lug nut. You will have to change the quantity ordered to match the number of lug nuts you need. What trailer are you working on?

view full answer...

Answer 7

Hey Benjamin, I would recommend the Powerbuilt Unijack part #ALL620471 as it has a 6,000 lb capacity which would be enough for both the trailer and your GMC Sierra 1500. It also has a jack stand built into it as well which makes it a little safer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hello Joe, Thank you for reaching out! The Power Mountain Tallboy Off-Road Bottle Jack - 11-5/16" to 27-1/16" Lift - 12 Tons #PM94FR does have the capacity you’d need, but since your fifth wheel’s frame sits about 25" off the ground,…

view full answer...

Can the EZ-Jack be Used on a Triple Axle Trailer

Product Page this Question was Asked From

Continue Researching