3/4 Inch Conical Washer, Bolt and Nut

Question

Question:

I need 3/4 inch conical washer and 3/4 inch bolts 4 1/2 inches long?

asked by: Jeffrey

0

Expert Reply:

We have the 3/4" Conical Washer # 3232 and 3/4" Bolt # 090747 that is 4-1/2" long. There is also the 3/4" Nut # F2135823295 with the same 16 threads per inch as the bolt.

expert reply by: Bud M

0

Answer 1

Yes, the Disc Brake Caliper for Dexter 10,000-lb to 12,000-lb Hydraulic Disc Brakes #e58GR that you mentioned is the same thing as the Dexter 89-2 calipers that you mentioned and will work great as a replacement. These calipers will work great with…

view full answer...

Answer 2

The Disc Brake Caliper for Dexter 10,000-lb to 12,000-lb Hydraulic Disc Brakes #e58GR is not designed for any particular trailer model but rather any 10,000-lbs to 12,000-lbs Dexter hydraulic disc brakes and will work on both the passenger and driver…

view full answer...

Answer 3

A caliper like the Disc Brake Caliper for Dexter 10K & 12K Hydraulic Disc Brakes #BP18-045 uses four of the #010-062-00 O-rings. These are designed to go onto the brake caliper guide bolts, two for each bolt. If you need additional parts we have…

view full answer...

Answer 4

The Equalizer Suspension Bolt #090747 is a grade 5 bolt.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

3/4 Inch Conical Washer, Bolt and Nut

Products Featured in This Question

Continue Researching