Availability of 14 inch Aluminum Trailer Wheel with Removable Center Cap Plug for Bearing Buddy

Question

Question:

Do any of your alum 14inch wheels have a center hub cover that accepts a bearing buddy. Dose it have a removable cap to grease?

asked by: Mike A

0

Expert Reply:

With the Aluminum Sendel Series T02 Machined Trailer Wheel # AM22329 that has a 3.19 inch diameter center hole you could use the center cap part # AM90175 which has a removable center plug that could access a Bearing Buddy.

expert reply by: Jameson C

0

Answer 1

The Lionshead Trailer Wheel Center Cap w/ Snap-In Plug part #LHCS102-SI60C is 3.5" deep. This can then be used to determine compatibility with a buddy bearing.

view full answer...

Answer 2

The center cap on Aluminum Hi-Spec Series T07 Trailer Wheel #AM25DR has an inner diameter of 2.8 inches and measures approximately 4.9 inches from the mounting surface at the back of the wheel (hub face) to the outermost part on the inside for the…

view full answer...

Answer 3

The Aluminum Viking Series Vor Trailer Wheel - 14" x 5-1/2" - 5 on 4-1/2 - Silver #AX02455545FPS you were looking at does come with a valve stem and center cap included. The #AX02455545FPS is a great choice due to the aluminum construction…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 7

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 8

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

Hello George, thanks for reaching out. We certainly should have a hub option for you. I see that your trailer has a 2,500 lb axle. We do carry hubs for this, but there are a few possible options depending on what bearings/spindle size your trailer…

view full answer...

Answer 12

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Availability of 14 inch Aluminum Trailer Wheel with Removable Center Cap Plug for Bearing Buddy

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching